S.C. Code Regs. § § 61-58.3.C

Current through Register Vol. 48, No. 11, November 22, 2024

Section 61-58.3.C - General Design Requirements

(1) Plant Layout--Design shall provide for adequate access roads, site drainage, protection of basins from spillage (including during delivery of chemical shipments), and adequate protection from vandalism. Consideration shall also be given to functional aspects of the plant layout and future expansion.

(2) Building layout--Design shall provide for adequate ventilation, lighting, telephone service, heating and air conditioning, floor drainage, and, if necessary, dehumidification equipment. Consideration shall also be given to accessibility of equipment for operation, servicing, and removal, telephone communication capability, flexibility of operation, operator safety, and convenience of operation (filters, basins, etc. visible to the operator).

(3) Electrical controls--Main switch gear electrical controls shall be located above grade and be protected from standing water.

(4) Auxiliary Power--Where elevated storage equals less than one half maximum daily demand, portable or in-place auxiliary power shall be provided for all systems serving three hundred (300) or more service connections. An air quality permit may be required for the emissions from the auxiliary generators. Auxiliary power requirements may be waived if one or more of the following are applicable:

(a) A verifiable history of worst case power outages and verification that the available elevated storage can provide for a similar time period of outage.

(b) Two (2) or more independent sources from the serving electrical utility are available. or,

(c) An alternate water source is available via connections with other systems.

Auxiliary power shall be sized to provide for sufficient pumping and treatment capacity to meet one half ( 1/2) of the maximum daily demand or to supplement the existing storage to meet one half ( 1/2) of the maximum daily demand.

(5) Sample taps--Sample taps shall be provided so that representative water samples can be obtained from:

(a) each raw water source;

(b) appropriate locations throughout the treatment process so that the operator can maintain proper control of the treatment process;

(c) effluent from each filter and the combined filter effluent prior to any post chemical addition; and,

(d) the entry point(s) to the distribution system.

Taps shall be consistent with sampling needs and shall not be of the petcock type. Taps used for obtaining samples for bacteriological analysis shall be of the smooth-nosed type without interior or exterior threads. Taps shall not be of the mixing type, and shall not have a screen, aerator, or other such appurtenances.

(6) Monitoring Equipment

(a) Complete bacteriological and wet chemistry testing equipment is required for all surface water plants for daily monitoring of raw, coagulated, settled, filtered and finished water quality.

(b) Laboratory equipment and facilities shall be compatible with the raw water source, the intended use of the treatment plant and the complexity of the treatment process involved. Plants treating surface water shall have as a minimum the capability to monitor turbidity, appropriate disinfectant residual, pH, temperature, alkalinity, calcium hardness, and if added, fluoride, total phosphate or orthophosphate and silica.

(7) Plant Water--The treatment plant water service line and the plant finished water sample tap shall be supplied from a source of finished water at a point where all chemicals have been thoroughly mixed.

(8) Wall Castings--Consideration shall be given to providing extra wall castings built into the structure to facilitate future uses whenever pipes pass through walls of concrete structures.

(9) Flow Meters--Flow meters shall be provided for measuring raw and finished water, all backwash water, and where deemed necessary, other internal water uses at all surface water plants. Meters shall measure an instantaneous flow and have the capability to measure totalized flow.

(10) Piping Identification--To facilitate identification of piping in treatment plants and pumping stations, all pipes shall be color coded and marked with the name of the liquid or gas being carried and its direction of flow.

(11) Proprietary Treatment Units/ Innovative Treatment Techniques--Proprietary treatment units and alternative treatment technology may be considered if pilot tests demonstrate the ability of the technology to provide water which meets all drinking water standards utilizing the proposed raw water source. If the plant is permitted at rates which exceed the unit process rates specified in R.61-58.3(D)(D), the system shall submit operating data within eighteen (18) months which justify continued operation at the higher rates. From the review of these data, the Department may revise the permitted treatment rate.

(12) Manuals and Parts Lists--An operation and maintenance manual shall be provided for each treatment plant. This manual shall, at a minimum, include repair information, parts lists for each piece of equipment, and procedures for the start up and shut down of the plant including all necessary chemical treatment systems.

(13) Safety--All design must meet applicable safety codes and minimum Occupational Safety and Health Administration (OSHA) standards.

S.C. Code Regs. § 61-58.3.C