Section 42310.2 - Regulations adopted to carry out section 42310.1(c)(1) requirements; review of reports; agreements with trade associations(a) On or before July 1, 1994, as part of the regulations required to be adopted pursuant to Section 42325, the board shall adopt regulations to carry out the requirements of paragraph (1) of subdivision (c) of Section 42310.1. In adopting regulations pursuant to this section, the board shall make every effort to limit paperwork and information to only those matters that are needed for the board to determine if manufacturers are taking all feasible actions to ensure the reduction, recycling, or reuse of the rigid plastic packaging containers described in subdivision (a) of Section 42310.1, and the development and expansion of markets for rigid plastic packaging containers.(b) On or before February 1, 1996, the board shall review, and approve or disapprove, the reports required pursuant to paragraph (1) of subdivision (c) of Section 42310.1. If a report is not submitted pursuant to a schedule established by the board, or, if, based upon the report, the board determines that a manufacturer has not taken all feasible actions to ensure the reduction, recycling, or reuse of the containers and the development and expansion of markets for rigid plastic packaging containers, the board may take one of the following actions, as selected by the manufacturer:(1) Require the manufacturer to take additional actions, including, but not limited to, one or more of the measures described in paragraph (1) of subdivision (c) of Section 42310.1, to ensure that the manufacturer is taking, and will continue to take, all feasible actions to ensure the reduction, recycling, or reuse of the containers and the development and expansion of markets for rigid plastic packaging containers.(2) Impose a civil penalty of up to one hundred thousand dollars ($100,000) pursuant to Section 42322. In imposing monetary penalties pursuant to this paragraph, the board shall take into consideration all of the following factors: (A) The size and net worth of the manufacturer.(B) The impact of the violation on the overall objectives of this chapter.(C) The severity of the violation. A penalty imposed pursuant to this paragraph shall not be required to be paid by a manufacturer before January 1, 1997.(c) If the board determines that the conditions in paragraphs (1) and (2) are met, the board shall enter into a contract, or other legally binding agreement, with one or more trade associations representing manufacturers of resin, manufacturers of rigid plastic packaging containers, or manufacturers of products packaged in rigid plastic packaging containers subject to this section and Section 42310.1. The agreement shall allow the trade association, in lieu of those individual manufacturers in the trade association who elect to be a party to the contract or agreement, to submit the report required pursuant to paragraph (1) of subdivision (c) of Section 42310.1 and to implement the actions identified in the report. The board shall enter into the agreement only if both of the following conditions exist: (1) The agreement ensures that the report will contain sufficient information that otherwise would be required to be submitted by individual manufacturers pursuant to Section 42310.1, and any other information that is necessary and directly related to the board's ability to comply with this section.(2) The agreement ensures that each manufacturer that elects to be a party to the agreement and that is a member of the trade association that submits the report shall be liable for the full amount of any civil penalties that may be imposed or shall comply with any requirement imposed by the board pursuant to paragraph (1) of subdivision (b), as selected by the manufacturer. A manufacturer subject to this paragraph shall not be liable for a civil penalty greater than one hundred thousand dollars ($100,000), regardless of the number of trade associations of which the manufacturer is a member.(d) Notwithstanding any other provision of this section, a trade association representing resin manufacturers shall be responsible for submitting an additional report as provided pursuant to paragraph (1) of subdivision (c) of Section 42310.1. The resin manufacturer's trade association is subject to the review, penalties, and sanctions specified in paragraphs (1) and (2) of subdivision (b). No member of the resin manufacturer's trade association is liable for penalties and sanctions set forth in paragraph (1) or (2) of subdivision (b) pursuant to this subdivision if that member would not otherwise be subject to those penalties and sanctions.(e) For the purposes of subdivision (b) and paragraph (1) of subdivision (c) of Section 42310.1, "feasible" means capable of being accomplished in a successful manner within a reasonable period of time, taking into account economic, environmental, social, and technological factors.(f) For purposes of Section 42310.1 and this section regarding all reporting, compliance, and penalty obligations, "manufacturer" includes all subsidiaries and affiliates.Ca. Pub. Res. Code § 42310.2
Amended by Stats 2004 ch 561 (SB 1729), s 3, eff. 1/1/2005.