Wis. Admin. Code Department of Natural Resources NR 440.17

Current through November 25, 2024
Section NR 440.17 - Incorporation by reference of code of federal regulations provisions and other materials
(1) APPENDICES. Appendices A, B, C, F and I of 40 CFR part 60, Appendix B of 40 CFR part 61 and Appendices A, B, D, E and F of 40 CFR part 75, as in effect on June 1, 2008, are incorporated by reference and made a part of this chapter. Copies of these Appendices are available for inspection in the offices of the department of natural resources and legislative reference bureau, Madison, Wisconsin, or may be purchased for personal use from the superintendent of documents, U.S. government printing office, Washington DC 20402.
(2) OTHER MATERIALS. The materials listed in this subsection are incorporated by reference for the corresponding sections noted. Some of the materials are also incorporated for Appendices A, B, C and F of 40 CFR part 60 as in effect on June 1, 2008. Since these Appendices are incorporated by reference in this chapter by sub. (1), materials incorporated by reference in the Appendices are hereby also incorporated by reference and made a part of this chapter. The materials are available for inspection in the offices of the department of natural resources and legislative reference bureau, Madison, Wisconsin or may be purchased for personal use at the corresponding address noted.
(a) The materials listed in Table 1 are available for purchase from at least one of the following addresses: American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West Conshohocken PA 19428-2959, Phone: 610.832.9585, Fax: 610.832.9555, E-mail: service@astm.org, Website: http://www.astm.org or IHS Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112, Phone: 800.854.7179, E-mail: globalcustomerservice@ihs.com, Website: http://global.ihs.com.

Table 1

ASTM Standard References

Standard NumberStandard TitleIncorporated by Reference For
1. ASTM A99-82 (reapproved 1987) Standard Specification for Ferromanganese NR 440.43(2) (v)
2. ASTM A100-93 Standard Specification for Ferrosilicon NR 440.43(2) (k) and (t)
3. ASTM A101-93 Standard Specification for Ferrochromium NR 440.43(2) (o)
4. ASTM A482-93 Standard Specification for Ferrochromesilicon NR 440.43(2) (i)
5. ASTM A483-74 (reapproved 1988) Standard Specification for Silicomanganese NR 440.43(2) (q)
6. ASTM A495-94 Standard Specification for Calcium-Silicon and Calcium Manganese-Silicon NR 440.43(2) (c)
7. ASTM D86-96 Distillation of Petroleum Products NR 440.647(4) (d)
NR 440.66(4) (d)
NR 440.682(4) (h)
8. ASTM D129-00 Standard Test Method for Sulfur in Petroleum Products (General Bomb Method) 40 CFR part 60, Appendix A, Method 19, section 12.5.2.2.3
NR 440.26(7) (j) 2.
NR 440.50(6) (d) 1.
9. ASTM D240-92 Standard Test Method for Heat of Combustion of NR 440.19(7) (c) 2.
Liquid Hydrocarbon Fuels by Bomb Calorimeter NR 440.46(7) (b) 3.
40 CFR part 60, Appendix A, Method 19, section 12.5.2.2.3.
10. ASTM D270-75 [Withdrawn] Standard Method of Sampling Petroleum and Petroleum Products 40 CFR part 60, Appendix A, Method 19, section 12.5.2.2.1.
11. ASTM D323-94 Test Method for Vapor Pressure of Petroleum Products (Reid Method) NR 440.27(2) (i)
NR 440.28(2) (h)
NR 440.285(2) (i) and (7) (f) 2. b.
12. ASTM D388-99 (reapproved 2004) Standard Specification for Classification of Coals by Rank NR 440.19(2) (a) and (6) (f) 4. a., b. and f.
NR 440.20(2) (b), (n) and (y)
NR 440.205(2) (d) and (t)
NR 440.207(2) (b)
NR 440.42(2) (a) and (b)
13. ASTM D396-98 Standard Specification for Fuel Oils NR 440.205(2) (h) and (zf)
NR 440.207(2) (g) and (v)
NR 440.27(2) (g)
NR 440.28(2) (f)
14. ASTM D975-98a Standard Specification for Diesel Fuel Oils NR 440.27(2) (g)
NR 440.28(2) (f)
15. ASTM D1072-9(reapproved 1994)0 Standard Method for Total Sulfur in Fuel Gases NR 440.50(6) (d) 2.
16. ASTM D1137-75 Standard Method for Analysis of Natural Gases and NR 440.19(6) (f) 5. a.
Related Types of Gaseous Mixtures by the Mass
Spectrometer
17. ASTM D1193-91 Standard Specification for Reagent Water 40 CFR part 60, Appendix A, Method 5, section
7.1.3; Method 5E, sectio n 7.2.1; Method 5F,
section 7.2.1; Method 6, section 7.1.1; Method
7, section 7.1.1; Method 7C, section 7.1.1;
Method 7D, sectio n 7.1.1; Method 10A, section
7.1.1; Method 11, section 7.1.3; Method 12,
section 7.1.3; Method 13A, section 7.1.2;
Method 14A, section 7.1; Method 25D, section
7.2.2.4; Method 26, section 7.1.2; Method 26A,
section 7.1.2; Method 29, section 7.2.2.
18. ASTM D1266-98 Standard Test Method for Sulfur in Petroleum Products (Lamp Method)NR 440.26(7) (j) 2.
NR 440.50(6) (d) 1.
19. ASTM D1475-90 Standard Test Method for Density of Paint, Varnish NR 440.56(6) (d) 1.
Lacquer, and Related Products 40 CFR part 60, Appendix A, Method 24, section
6.1, Method 24A, sections 6.5 and 7.1.
20. ASTM D1552-01 Standard Test Method for Sulfur in Petroleum Products40 CFR part 60, Appendix A, Method 19, section 12.5.2.2.3
(High Temperature Method)
NR 440.26(7) (j) 2.
NR 440.50(6) (d) 1.
21. ASTM D1826-94 Standard Test Method for Calorific Value of Gases in NR 440.19(6) (f) 5. b. and (7) (c) 2.
Natural Gas Range by Continuous Recording Calorimeter NR 440.46(7) (b) 3.
40 CFR part 60, Appendix A, Method 19, section 12.3.2.4.
22. ASTM D1835-97 Standard Specification for Liquefied Petroleum (LP) GasesNR 440.205(2) (y)
NR 440.207(2) (q)
23. ASTM D1945-96 Standard Method for Analysis of Natural Gas by Gas Chromatography NR 440.19(6) (f) 5. a.
24. ASTM D1946-90 (reapproved 1994) Standard Method for Analysis of Reformed Gas by Gas ChromatographyNR 440.18(6) (c)
NR 440.19(6) (f) 5. a.
NR 440.647(6) (f)
NR 440.675(5) (e) 3. b. and 5.
NR 440.686(5) (e) 2. b. and 4.
NR 440.705(5) (d) 2. b. and 4.
25. ASTM D2013-86 Standard Method of Preparing Coal Samples for Analysis 40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
26. ASTM D2015-96 Standard Test Method for Gross Calorific Value of NR 440.19(6) (f) 5. b. and (7) (c) 2.
Solid Fuel by the Adiabatic Bomb Calorimeter 40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
27. ASTM D2016-83 Standard Test Methods for Moisture Content of Wood 40 CFR part 60, Appendix A, Method 28, section 16.1.1.
28. ASTM D2234-98 Standard Methods for Collection of a Gross Sample of Coal 40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.1.
29. ASTM D2369-95 Standard Test Method for Volatile Content of Coatings 40 CFR part 60, Appendix A, Method 24, section 6.2.
30. ASTM D2382-88 Heat of Combustion of Hydrocarbon Fuels by Bomb NR 440.18(6)
Calorimeter (High-Precision Method) NR 440.62(6) (g) 6.
NR 440.647(6) (f)
NR 440.675(5) (e) 5.
NR 440.686(5) (e) 4.
NR 440.705(5) (d) 4.
31. ASTM D2504-88 (reapproved 1993) Noncondensable Gases in C3 and Lighter Hydrocarbon Products by Gas Chromatography NR 440.62(6) (g) 5.
32. ASTM D2584-94 Standard Test Method for Ignition Loss of Cured Reinforced Resins NR 440.69(6) (c) 3. a.
33. ASTM D2597-94 (reapproved 1999) Standard Test Method for Analysis of Demethanized NR 440.50(6) (c) 9. a.
Hydrocarbon Liquid Mixtures Containing Nitrogen
and Carbon Dioxide by Gas Chromatography
34. ASTM D2622-98 Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence SpectrometryNR 440.26(7) (j) 2.
NR 440.50(6) (d) 1.
35. ASTM D2879-97 Test Method for Vapor Pressure-Temperature Relationship and Initial Decomposition Temperature of Liquids by IsoteniscopeNR 440.285(2) (f) 3., (7) (e) 3. b. and (f) 2. a.
NR 440.62(6)(e)1.
36. ASTM D2880-96 Standard Specification for Gas Turbine Fuel Oils NR 440.27(2) (g)
NR 440.28(2) (f)
NR 440.50(6) (d)
37. ASTM D2908-91 Standard Practice for Measuring Volatile Organic NR 440.647(6) (j)
Matter in Water by Aqueous-Injection Gas Chromatography
38. ASTM D2986-95a Standard Method for Evaluation of Air, Assay Media 40 CFR part 60, Appendix A, Method 5, section
by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test 7.1.1, Method 12, section 7.1.1, and Method 13A, section 7.1.1.2.
39. ASTM D3031-81 Standard Test Method for Total Sulfur in Natural Gas by Hydrogenation NR 440.50(6) (d)
40. ASTM D3173-87 Standard Test Method for Moisture in the Analysis Sample of Coal and Coke 40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
41. ASTM D3176-89 Standard Method for Ultimate Analysis of Coal and CokeNR 440.19(6) (f) 5. a.
40 CFR part 60, Appendix A, Method 19, section 12.3.2.3.
42. ASTM D3177-89 Standard Test Method for Total Sulfur in the Analysis Sample of Coal and Coke40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
43. ASTM D3178-89 Standard Test Methods for Carbon and Hydrogen in the Analysis Sample of Coal and CokeNR 440.19(6) (f) 5. a.
44. ASTM D3246-96 Standard Method for Sulfur in Petroleum Gas by Oxidative Microcoulometry NR 440.50(6) (d) 2.
45. ASTM D3270-95 Standard Test Methods for Analysis for Fluoride Content of the Atmosphere and Plant Tissues (Semiautomated Method)40 CFR part 60, Appendix A, Method 13A, section 16.1.
46. ASTM D3286-96 Standard Test Method for Gross Calorific Value of Coal and Coke by the Isoperibol Bomb Calorimeter 40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
47. ASTM D3370-95a Standard Practices for Sampling Water NR 440.647(6) (j)
48. ASTM D3431-80 (reapproved 1987) Test Method for Trace Nitrogen in Liquid Petroleum HydrocarbonsNR 440.205(10) (e)
49. ASTM D3792-91 Standard Test Method for Water Content of Water Reducible Paints by Direct Injection into a Gas Chromatograph 40 CFR part 60, Appendix A, Method 24, section 6.3.
50. ASTM D4017-96a Standard Test Method for Water in Paints and Paint Materials by the Karl Fischer Titration Method 40 CFR part 60, Appendix A, Method 24, section 6.4.
51. ASTM D4057-95 Standard Practice for Manual Sampling of Petroleum and Petroleum Products40 CFR part 60, Appendix A, Method 19, section 12.5.2.2.3.
52. ASTM D4084-94 Standard Method for Analysis of Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method) NR 440.50(5) (h) 1.
53. ASTM D4177-95 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products 40 CFR part 60, Appendix A, Method 19, section 12.5.2.2.1.
54. ASTM D4239-97 Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High Temperature Tube Furnace Combustion Methods40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
55. ASTM D4294-02 Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence SpectrometryNR 440.50(6) (d) 1.
56. ASTM D4442-92 Standard Test Methods for Direct Moisture Content Measurement in Wood and Wood-base Materials40 CFR part 60, Appendix A, Method 28, section 16.1.1.
57. ASTM D4444-92 Standard Test Methods for Use and Calibration of Hand-Held Moisture Meters40 CFR part 60, Appendix A, Method 28, section 16.1.1.
58. ASTM D4457-85 (reapproved 1991) Test Method for Determination of Dichloromethane and 1,1,1-Trichloroethane in Paints and Coatings by Direct Injection into a Gas Chromatograph40 CFR part 60, Appendix A, Method 24, section 6.5.
59. ASTM D4468-85 (reapproved 2000) Standard Test Method for Total Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric ColorimetryNR 440.50(6) (d) 2.
60. ASTM D4629-02 Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence DetectionNR 440.50(6) (c) 9. a.
61. ASTM D4809-95 Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)NR 440.18(6) (c)
NR 440.62(6) (g) 6.
NR 440.647(6) (f) 3.
NR 440.675(5) (e) 5.
NR 440.686(5) (e) 4.
NR 440.705(5) (d) 4.
63. ASTM D5403-93 Standard Test Methods for Volatile Content of Radiation Curable Materials 40 CFR part 60, Appendix A, Method 24, section 6.6.
64. ASTM D5453-00 Standard Test Method for Determination of Total Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet FluorescenceNR 440.50(6) (d) 1.
65. ASTM D5504-01 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and ChemiluminescenceNR 440.50(5) (h) 1.
66. ASTM D5762-02 Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet ChemiluminescenceNR 440.50(6) (c) 9. a.
67. ASTM D5865-98 Standard Test Method for Gross Calorific Value of Coal and CokeNR 440.19(6) (f) 5. b. and (7) (c) 2.
40 CFR part 60, Appendix A, Method 19, section 12.5.2.1.3.
68. ASTM D6216-98 Standard Practice for Opacity Monitor Manufacturers to Certify Conformance with Design and Performance Specifications40 CFR part 60, Appendix B, Performance Specification 1
69. ASTM D6228-98 Standard Test Method for Determination of Sulfur Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and Flame Photometric Detection NR 440.50(5) (h) 1.
70. ASTM D6366-99 Standard Test Method for Total Trace Nitrogen and Its Derivatives in Liquid Aromatic Hydrocarbons by Oxidative Combustion and Electrochemical Detection NR 440.50(6) (c) 9. a.
71. ASTM D6522-00 Standard Test Method for Determination of Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions from Natural Gas-Fired Reciprocating Engines, Combustion Turbines, Boilers, and Process Heaters Using Portable Analyzers NR 440.50(6) (a) 2. and (c) 4.
72. ASTM D6667-01 Standard Test Method for Determination of Total Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases by Ultraviolet Fluorescence NR 440.50(6) (d) 2.
75. ASTM E168-92 General Techniques of Infrared Quantitative Analysis NR 440.62(6) (d) 1.NR 440.66(4) (b) 2.NR 440.682(3) (f)
76. ASTM E169-93 General Techniques of Ultraviolet Quantitative Analysis NR 440.62(6) (d) 1.
NR 440.66(4) (b)NR 440.682(3) (f)
77. ASTM E260-96 General Gas Chromatography Procedures NR 440.62(6) (d) 1.NR 440.66(4) (b) 2.NR 440.682(3) (f)NR 440.684(5) (b) 3.

(b) The following material is available for purchase from the Association of Official Analytical Chemists, 1111 North 19th Street, Suite 210, Arlington VA 22209:
1. AOAC Method 9, Official Methods of Analysis of the Association of Official Analytical Chemists, 11th edition, 1970, pp. 11-12, for ss. NR 440.37(5) (b) 3. b., 440.38 (5) (b) 3. b., 440.39 (5) (b) 3. b., 440.40 (5) (b) 3. b., and 440.41 (5) (c) 3. b.
(c) The following material is available for purchase from the American Petroleum Institute, 1220 L Street NW, Washington DC 20005:
1. API Publication 2517, Evaporation Loss from External Floating-Roof Tanks, Second Edition, February 1980, for ss. NR 440.27(2) (k) and (4) (b), 440.28 (2) (j) and (6) (b), and 440.285 (2) (f) 1. and (7) (e) 2. a.
(d) The following material is available for purchase from the Technical Association of the Pulp and Paper Industry (TAPPI), Dunwoody Park, Atlanta GA 30341:
1. TAPPI Method T624 os-68, for s. NR 440.45(6) (d) 3.
(e) The following material is available for purchase from the American Public Health Association, PO Box 753, Waldorf MD 20604:
1. Method 2540 B., Total Solids Dried at 103-105°C, in Standard Methods for the Examination of Water and Wastewater, 20th edition, 1998, for s. NR 440.69(4) (b).
2. Method 2540 G., Total, Fixed, and Volatile Solids in Solid and Semisolid Samples, in Standard Methods for the Examination of Water and Wastewater, 20th edition, 1998, for s. NR 440.32(5) (b) 5.
3. Method 3112 B, Cold-Vapor Atomic Absorption Spectrometric Method, in Standard Methods for the Examination of Water and Wastewater, 20th edition, 1998, for 40 CFR part 60, Appendix A, Method 29, pars. 9.2.3, 10.3 and 11.1.3.
(f) The following material is available for purchase from the following address: Underwriter's Laboratories, Inc. (UL), 333 Pfingsten Road, Northbrook IL 60062:
1. UL 103, Sixth Edition revised as of September 3, 1986, Standard for Chimneys, Factory-built, Residential Type and Building Heating Appliance, for 40 CFR part 60, Appendix A, Method 28.
(g) The following material is available for purchase from the following address: West Coast Lumber Inspection Bureau, 6980 SW Barnes Road, Portland OR 97223:
1. West Coast Lumber Standard Grading Rules No. 16, pages 5-21 and 90 and 91, September 3, 1970, revised 1984, for 40 CFR, part 60, Appendix A, Method 28.
(h) The following material is available for purchase from the following address: The American Society of Mechanical Engineers (ASME), 22 Law Drive, Fairfield NJ 07004:
1. ASME QRO-1-1994, Standard for the Qualification and Certification of Resource Recovery Facility Operators, for ss. NR 440.215(7) (d), 440.216 (8) and (b) and 440.76(6) (a) 1. and 3. b.
2. ASME PTC 4.1, Power Test Codes: Test Code for Steam Generating Units, 1964, for ss. NR 440.205(7) (g), 440.215(9) (h) 6. b., 440.216 (12) (i) 6. b. and 440.76 (11) (b) 1. c.
3. ASME Interim Supplement 19.5 on Instruments and Apparatus; Application, Part II of Fluid Meters, 6th Edition, 1971, for ss. NR 440.215(9) (h) 6. b., 440.216 (12) (i) 6. b. and 440.76 (11) (b) 1. d.
(i) The following material is available from the National Technical Information Service, 5285 Port Royal Road, Springfield VA 22161:
1. The Standard Industrial Classification Manual, 1987, NTIS order no. PB 87-100012, for ss. NR 440.205(2) (c), (zb) and (zdm), 440.46(2) (c), (d), (i) and (L) and 440.72(2) (a) 1.
2. EPA AP-42, Compilation of Air Pollutant Emission Factors, Volume 1: Stationary Point and Area Sources, Fifth Edition, January 1995, as amended by Supplement A (February 1996), Supplement B (November 1996), Supplement C (November 1997), Supplement D (July 1998), Supplement E (November 1999), Supplement F (October 2000) and Update 2001 (December 2001), for ss. NR 440.14(2) (a) and 440.75 (5) (a) 3., (b) 3., (c) and (d) and (6) 1.
3. The North American Industry Classification System United States, 2002, NTIS order no. PB2002-101430, for s. NR 440.205(2) (zdm).
4. EPA document "Fabric Filter Bag Leak Detection Guidance" (EPA-454/R-98-015), for s. NR 440.445(4) (e) 4. (intro.). Copies of this document may also be downloaded from the internet for personal use from http://www.epa.gov/ttn/emc/cem/tribo.pdf.
(j) The following material is available for purchase from the Industrial Press Inc., 200 Madison Ave, New York NY 10016: Gas Engineers Handbook, 1st edition, 2nd printing, 1966, page 6/25, Fuel Gas Engineering Practice, for s. NR 440.684(9).
(k) Test Methods for Evaluating Solid Waste, Physical/Chemical Methods, EPA Publication SW-846 Third Edition (November 1986), as amended by Updates I (July, 1992), II (September 1994), IIA (August, 1993) and IIB (January, 1995) and III (December, 1996), for 40 CFR part 60, Appendix A, Method 29, pars. 7.5.34, 9.2.1, 9.2.3, 10.2, 10.3, 11.1.1, 11.1.3, 13.2.1, 13.2.2, 13.3.1, and Table 29-3. The Third Edition of SW-846 and Updates I, II, IIA, IIB and III (document number 955-001-00000-1) are available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402, (202) 512-1800. Copies may be obtained from the Library of the U.S. Environmental Protection Agency, 401 M Street, SW, Washington, DC 20460.
(L) The following material is available for purchase from the American Hospital Association (AHA) Service, Inc., PO Box 92683, Chicago, IL 60675-2683. You may inspect a copy at EPA's Air and Radiation Docket and Information Center (Docket A-91-61, Item IV-J-124), Room M-1500, 401 M Street SW, Washington, DC.
1. An Ounce of Prevention: Waste Reduction Strategies for Health Care Facilities, American Society for Health Care Environmental Services of the American Hospital Association, Chicago, IL, 1993, AHA Catalog No. 057007, ISBN 0-87258-673-5, for s. NR 440.218(6).
(m) The following material is available for purchase from either the Gas Processors Association, 6526 East 60th Street, Tulsa OK, 74145; or Information Handling Services, 15 Inverness Way East, PO Box 1154, Englewood CO 80150-1154: Gas Processors Association Method 2377-86, Test for Hydrogen Sulfide and Carbon Dioxide in Natural Gas Using Length of Stain Tubes, for s. NR 440.50(5) (h) 1.

Wis. Admin. Code Department of Natural Resources NR 440.17

Cr. Register, January, 1984, No. 337, eff. 2-1-84; am. (1), (2) (intro.), (a) 1., 3., 7. to 10., 13., 20., 22. and 24. to 28., (2) (b) 1. and (c) (intro.), cr. (2) (a) 34. to 55., (2) (e) and (h) renum. (2) (e) to be (2) (g), Register, September, 1990, No. 417, eff. 10-1-90; am. (1) (a) (intro.) to 5. and (b), (2) (a) 1., 6. to 11., 20. and 34. to 45., (b) 1., (c) 1., (d) 1., (e) (intro.) and 1., r. (2) (a) 46. and (g), renum. (2) (a) 47. to 55., (f) and (h) to be (2) (a) 46., to 54., (i) and (j) and am. (2) (a) 46. and 49., (i) and (j), cr. (2) (a) 56. to 61., (e) 2., (f), (g) and (h), Register, June, 1993, No. 450, eff. 8-1-93; r. (1) (a), renum. (1) (b) to be (1) and am., (2) (h) 1. to be (2) (h) 2. and am., am. (2) (a) 6., 20., 38., (b) (intro.), (d), (e) 1., (h) (intro.), cr. (2) (h) 1., 3., Register, December, 1995, No. 480, eff. 1-1-96; am. (2) (f) 1. and (g) 1., Register, April, 1997, No. 496, eff. 5-1-97; CR 06-109: am. (1), (2) (intro.), (e), (h) 1. to 3. and (i) 1. and 2., r. and recr. (2) (a), cr. (2) (e) 3., (i) 3. and 4. and (k) to (m) Register May 2008 No. 629, eff. 6-1-08; corrections in (1) and (2) made under s. 13.92(4) (b) 6, Stats., Register May 2008 No. 629.