9 Va. Admin. Code § 5-60-100
40 CFR 63.1 through 40 CFR 63.11; 40 CFR 63.16
(applicability, definitions, units and abbreviations, prohibited activities and circumvention, construction and reconstruction, compliance with standards and maintenance requirements, performance testing requirements, monitoring requirements, notification requirements, recordkeeping and reporting requirements, control device requirements, performance track provisions)
40 CFR 63.60, 40 CFR 63.61, 40 CFR 63.62, 40 CFR 63.63, and 40 CFR 63.64
(deletion of caprolactam from the list of hazardous air pollutants, deletion of methyl ethyl ketone from the list of hazardous air pollutants, redefinition of glycol ethers listed as hazardous air pollutants, deletion of ethylene glycol monobutyl ether from the list of hazardous air pollutants, addition of 1-bromopropane (1-BP) to the list of hazardous air pollutants)
40 CFR 63.100 through 40 CFR 63.106
(chemical manufacturing process units that manufacture as a primary product one or more of a listed chemical; use as a reactant or manufacture as a product, by-product, or co-product, one or more of a listed organic hazardous air pollutant; and are located at a plant site that is a major source as defined in § 112 of the federal Clean Air Act)
40 CFR 63.110 through 40 CFR 63.152
(all process vents, storage vessels, transfer operations, and wastewater streams within a source subject to Subpart F, 40 CFR 63.100 through 40 CFR 63.106)
40 CFR 63.160 through 40 CFR 63.182
(pumps, compressors, agitators, pressure relief devices, sampling connection systems, open-ended valves or lines, valves, connectors, surge control vessels, bottoms receivers, instrumentation systems, and control devices or systems that are intended to operate in organic hazardous air pollutant service 300 hours or more during the calendar year within a source subject to the provisions of a specific subpart in 40 CFR Part 63)
40 CFR 63.190 through 40 CFR 63.192
(emissions of designated organic hazardous air pollutants from processes specified in this subpart that are located at a plant site that is a major source as defined in § 112 of the federal Clean Air Act)
40 CFR 63.210 through 40 CFR 63.217
(NOTE: Authority to enforce the above standard is being retained by EPA and it is not incorporated by reference into these regulations.)
40 CFR 63.300 through 40 CFR 63.313
(existing by-product coke oven batteries at a coke plant, and existing nonrecovery coke oven batteries located at a coke plant)
40 CFR 63.320 through 40 CFR 63.325
(each dry cleaning facility that uses perchlorethylene)
40 CFR 63.340 through 40 CFR 63.347
(each chromium electroplating or chromium anodizing tank at facilities performing hard chromium electroplating, decorative chromium electroplating, or chromium anodizing)
40 CFR 63.360 through 40 CFR 63.367
(sterilization sources using ethylene oxide in sterilization or fumigation operations)
40 CFR 63.400 through 40 CFR 63.406
(industrial process cooling towers that are operated with chromium-based water treatment chemicals)
40 CFR 63.420 through 40 CFR 63.429
(bulk gasoline terminals and pipeline breakout stations)
40 CFR 63.440 through 40 CFR 63.458
(processes that produce pulp, paper, or paperboard, and use the following processes and materials: kraft, soda, sulfite, or semi-chemical pulping processes using wood; or mechanical pulping processes using wood; or any process using secondary or nonwood fibers)
40 CFR 63.460 through 40 CFR 63.469
(each individual batch vapor, in-line vapor, in-line cold, and batch cold solvent cleaning machine that uses any solvent containing methylene chloride, perchlorethylene, trichloroethylene, 1,1,1-trichloroethane, carbon tetrachloride, or chloroform)
40 CFR 63.480 through 40 CFR 63.506
(elastomer product process units that produce butyl rubber, halobutyl rubber, epichlorohydrin elastomers, ethylene propylene rubber, HypalonT, neoprene, nitrile butadiene rubber, nitrile butadiene latex, polysulfide rubber, polybutadiene rubber/styrene butadiene rubber by solution, styrene butadiene latex, and styrene butadiene rubber by emulsion)
40 CFR 63.520 through 40 CFR 63.527
(manufacturers of basic liquid epoxy resins and wet strength resins)
40 CFR 63.541 through 40 CFR 60.552
(at all secondary lead smelters: blast, reverberatory, rotary, and electric smelting furnaces; refining kettles; agglomerating furnaces; dryers; process fugitive sources; and fugitive dust sources)
40 CFR 63.560 through 40 CFR 63.567
(marine tank vessel unloading operations at petroleum refineries)
40 CFR 63.600 through 40 CFR 63.611
(wet-process phosphoric acid process lines, evaporative cooling towers, rock dryers, rock calciners, superphosphoric acid process lines, purified acid process lines)
40 CFR 63.620 through 40 CFR 63.632
(diammonium and monoammonium phosphate process lines, granular triple superphosphate process lines, and granular triple superphosphate storage buildings)
40 CFR 63.640 through 40 CFR 63.671
(storage tanks, equipment leaks, process vents, and wastewater collection and treatment systems at petroleum refineries)
40 CFR 63.680 through 40 CFR 63.697
(operations that treat, store, recycle, and dispose of waste received from other operations that produce waste or recoverable materials as part of their manufacturing processes)
40 CFR 63.701 through 40 CFR 63.708
(manufacturers of magnetic tape)
40 CFR 63.741 through 40 CFR 63.759
(facilities engaged in the manufacture or rework of commercial, civil, or military aerospace vehicles or components)
40 CFR 63.760 through 40 CFR 63.779
(facilities that process, upgrade, or store hydrocarbon liquids or natural gas; ancillary equipment and compressors intended to operate in volatile hazardous air pollutant service)
40 CFR 63.780 through 40 CFR 63.788
(shipbuilding and ship repair operations)
40 CFR 63.800 through 40 CFR 63.819
(finishing materials, adhesives, and strippable spray booth coatings; storage, transfer, and application of coatings and solvents)
40 CFR 63.820 through 40 CFR 63.831
(publication rotogravure, product and packaging rotogravure, and wide-web printing processes)
40 CFR 63.840 through 40 CFR 63.859
(each pitch storage tank, potline, paste production plant, or anode bulk furnace associated with primary aluminum production)
40 CFR 63.860 through 40 CFR 63.868
(chemical recovery systems, direct and nondirect contact evaporator recovery furnace systems, lime kilns, sulfite combustion units, semichemical combustion units)
40 CFR 63.880 through 40 CFR 63.899
(manufacture of wool fiberglass insulation materials composed of glass fibers made from glass produced or melted at the same facility where the manufacturing line is located)
40 CFR 63.900 through 40 CFR 63.907
(for off-site waste and recovery operations, fixed-roof tanks)
40 CFR 63.920 through 40 CFR 63.928
(for off-site waste and recovery operations, containers)
40 CFR 63.940 through 40 CFR 63.948
(for off-site waste and recovery operations, surface impoundment covers and vents)
40 CFR 63.960 through 40 CFR 63.966
(for off-site waste and recovery operations, inspection and maintenance of individual drain systems)
40 CFR 63.980 through 40 CFR 63.999
(closed vent systems, control devices, recovery devices, and routing to a fuel gas system or a process, when associated with facilities subject to a referencing subpart)
40 CFR 63.1000 through 40 CFR 63.1018
(control of air emissions from equipment leaks when associated with facilities subject to a referencing subpart)
40 CFR 63.1019 through 40 CFR 63.1039
(control of air emissions from equipment leaks when associated with facilities subject to a referencing subpart: pumps, compressors, agitators, pressure relief devices, sampling connection systems, open-ended valves or lines, valves, connectors, instrumentation systems, closed vent systems and control devices)
40 CFR 63.1040 through 40 CFR 63.1049
(for off-site waste and recovery operations, oil-water separators and organic-water separator roofs and vents)
40 CFR 63.1060 through 40 CFR 63.1066
(storage vessels associated with facilities subject to a referencing subpart)
40 CFR 63.1080 through 40 CFR 63.1098
(any cooling tower system or once-through cooling water system)
40 CFR 63.1100 through 40 CFR 63.1113
(acetal resins production, acrylic and modacrylic fibers production, hydrogen fluoride production, polycarbonate production)
40 CFR 63.1155 through 40 CFR 63.1174
(steel pickling facilities that pickle carbon steel using hydrochloric acid solution, hydrochloric acid regeneration plants)
40 CFR 63.1175 through 40 CFR 63.1199
(cupolas and curing ovens at mineral wool manufacturing facilities)
40 CFR 63.1200 through 40 CFR 63.1221
(hazardous waste combustors)
40 CFR 63.1250 through 40 CFR 63.1261
(pharmaceutical manufacturing operations)
40 CFR 63.1270 through 40 CFR 63.1289
(natural gas transmission and storage facilities that transport or store natural gas prior to entering the pipeline to a local distribution company or to a final end user)
40 CFR 63.1290 through 40 CFR 63.1309
(flexible polyurethane foam or rebond processes)
40 CFR 63.1310 through 40 CFR 63.1335
(facilities which manufacture acrylonitrile butadiene styrene resin, styrene acrylonitrile resin, methyl methacrylate butadiene styrene resin, polystyrene resin, poly(ethylene terephthalate) resin, or nitrile resin)
40 CFR 63.1340 through 40 CFR 63.1359
(kilns; in-line kilns/raw mills; clinker coolers; raw mills; finish mills; raw material dryers; raw material, clinker, or finished product storage bins; conveying system transfer points; bagging systems; bulk loading or unloading systems)
40 CFR 63.1360 through 40 CFR 63.1369
(pesticide active ingredient manufacturing process units, waste management units, heat exchange systems, and cooling towers)
40 CFR 63.1380 through 40 CFR 63.1399
(glass melting furnaces, rotary spin wool fiberglass manufacturing lines producing bonded wool fiberglass building insulation or bonded heavy-density product)
40 CFR 63.1400 through 40 CFR 63.1419
(unit operations, process vents, storage vessels, equipment subject to leak provisions)
40 CFR 63.1420 through 40 CFR 63.1439
(polyether polyol manufacturing process units)
40 CFR 63.1440 through 40 CFR 63.1-1459
(batch copper converters, including copper concentrate dryers, smelting furnaces, slag cleaning vessels, copper converter departments, and the entire group of fugitive emission sources)
40 CFR 63.1500 through 40 CFR 63.1520
(scrap shredders; thermal chip dryers; scrap dryers/delacquering kilns/decoating kilns; group 2, sweat, dross-only furnaces; rotary dross coolers; processing units)
40 CFR 63.1541 through 40 CFR 63.1550
(sinter machines, blast furnaces, dross furnaces, process fugitive sources, fugitive dust sources)
40 CFR 63.1560 through 40 CFR 63.1579
(petroleum refineries that produce transportation and heating fuels or lubricants, separate petroleum, or separate, crack, react, or reform an intermediate petroleum stream, or recover byproducts from an intermediate petroleum stream)
40 CFR 63.1580 through 40 CFR 63.1595
(intercepting sewers, outfall sewers, sewage collection systems, pumping, power, and other equipment)
40 CFR 63.1620 through 40 CFR 63.1679
(submerged arc furnaces, metal oxygen refining processes, crushing and screening operations, fugitive dust sources)
40 CFR 63.1930 through 40 CFR 63.1990
(municipal solid waste landfills that have accepted waste since November 8, 1987, or have additional capacity for waste deposition)
40 CFR 63.2130 through 40 CFR 63.2192
(fermentation vessels)
40 CFR 63.2230 through 40 CFR 63.2292
(manufacture of plywood and composite wood products by bonding wood material or agricultural fiber with resin under heat and pressure to form a structural panel or engineered wood product)
40 CFR 63.2330 through 40 CFR 63.2406
(transfer of noncrude oil liquids or liquid mixtures that contain organic hazardous air pollutants, or crude oils downstream of the first point of custody, via storage tanks, transfer racks, equipment leak components associated with pipelines, and transport vehicles)
40 CFR 63.2430 through 40 CFR 63.2550
(reaction, recovery, separation, purification, or other activity, operation, manufacture, or treatment that is used to produce a product or isolated intermediate)
40 CFR 63.2830 through 40 CFR 63.2872
(vegetable oil production processes)
40 CFR 63.2980 through 63.3079
(wet-formed fiberglass mat drying and curing ovens)
40 CFR 63.3080 through 40 CFR 63.3176.
(application of topcoat to new automobile or new light-duty truck bodies or body parts)
40 CFR 63.3280 through 40 CFR 63.3420
(web coating lines engaged in the coating of metal webs used in flexible packaging and in the coating of fabric substrates for use in pressure-sensitive tape and abrasive materials)
40 CFR 63.3480 through 40 CFR 63.3561
(application of coatings to a substrate using spray guns or dip tanks, including one-piece and two-piece draw and iron can body coating; sheetcoating; three-piece can body assembly coating; and end coating)
40 CFR 63.3880 through 40 CFR 63.3981
(application of coatings to industrial, household, and consumer products)
40 CFR 63.4080 through 40 CFR 63.4181
(surface coating of a large appliance part or product, including cooking equipment; refrigerators, freezers, and refrigerated cabinets and cases; laundry equipment; dishwashers, trash compactors, and water heaters; and HVAC units, air-conditioning, air-conditioning and heating combination units, comfort furnaces, and electric heat pumps)
40 CFR 63.4280 through 40 CFR 63.4371
(printing, coating, slashing, dyeing, or finishing of fabric and other textiles)
40 CFR 63.4480 through 40 CFR 63.4581
(application of coating to a substrate using spray guns or dip tanks, including motor vehicle parts and accessories for automobiles, trucks, recreational vehicles; sporting and recreational goods; toys; business machines; laboratory and medical equipment; and household and other consumer products)
40 CFR 63.4680 through 40 CFR 63.4781
(finishing or laminating of wood building products used in the construction of a residential, commercial, or institutional building)
40 CFR 63.4880 through 40 CFR 63.4981
(application of coatings to substrate using spray guns and dip tanks)
40 CFR 63.5080 through 40 CFR 63.5209
(organic coating to surface of metal coil, including web unwind or feed sections, work stations, curing ovens, wet sections, and quench stations)
40 CFR 63.5280 through 40 CFR 63.5460
(multistage application of finishing materials to adjust and improve the physical and aesthetic characteristics of leather surfaces)
40 CFR 63.5480 through 40 CFR 63.5610
(cellulose food casing, rayon, cellulosic sponge, cellophane manufacturing, methyl cellulose, hydroxypropyl methyl cellulose, hydroxypropyl cellulose, hydroxyethyl cellulose, and carboxymethyl cellulose manufacturing industries)
40 CFR 63.5680 through 40 CFR 63.5779
(resin and gel coat operations, carpet and fabric adhesive operations, aluminum recreational boat surface coating operations)
40 CFR 63.5780 through 40 CFR 63.5935
(reinforced or nonreinforced plastic composites or plastic molding compounds using thermostat resins and gel coats that contain styrene)
40 CFR 63.5980 through 40 CFR 63.6015
(production of rubber tires and components including rubber compounds, sidewalls, tread, tire beads, tire cord and liners)
40 CFR 63.6080 through 40 CFR 63.6175
(simple cycle, regenerative/recuperative cycle, cogeneration cycle, and combined cycle stationary combustion turbines)
40 CFR 63.6580 through 40 CFR 63.6675.
(any stationary internal combustion engine that uses reciprocating motion to convert heat energy into mechanical work)
(NOTE: Authority to enforce provisions related to affected facilities located at a major source as defined in 40 CFR 63.6675 is being retained by the Commonwealth. Authority to enforce the area source provisions of the above standard is being retained by EPA and are not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)
40 CFR 63.7080 through 40 CFR 63.7143.
(manufacture of lime product, including calcium oxide, calcium oxide with magnesium oxide, or dead burned dolomite, by calcination of limestone, dolomite, shells or other calcareous substances)
40 CFR 63.7180 through 40 CFR 63.7195
(semiconductor manufacturing process units used to manufacture p-type and n-type semiconductors and active solid-state devices from a wafer substrate)
40 CFR 63.7280 through 40 CFR 63.7352
(pushing, soaking, quenching, and battery stacks at coke oven batteries)
40 CFR 63.7480 through 40 CFR 63.7575
(industrial, commercial, and institutional boilers and process heaters)
40 CFR 63.7680 through 40 CFR 63.7765
(metal melting furnaces, scrap preheaters, pouring areas, pouring stations, automated conveyor and pallet cooling lines, automated shakeout lines, and mold and core making lines)
40 CFR 63.7780 through 40 CFR 63.7852
(each sinter plant, blast furnace, and basic oxygen process furnace at an integrated iron and steel manufacturing facility)
40 CFR 63.7880 through 40 CFR 63.7957
(activities or processes used to remove, destroy, degrade, transform, immobilize, or otherwise manage remediation material)
40 CFR 63.7980 through 40 CFR 63.8105
(process vessels; storage tanks for feedstocks and products; pumps, compressors, agitators, pressure relief devices, sampling connection systems, open-ended valves or lines, valves, connectors, and instrumentation systems; wastewater tanks and transfer racks)
40 CFR 63.8180 through 40 CFR 63.8266
(byproduct hydrogen streams, end box ventilation system vents, and fugitive emission sources associated with cell rooms, hydrogen systems, caustic systems, and storage areas for mercury-containing wastes)
40 CFR 63.8380 through 40 CFR 63.8515
(facilities that manufacture brick, clay pipe, roof tile, extruded floor and wall tile, and other extruded, dimensional clay products, and typically process raw clay and shale, form the processed materials into bricks or shapes, and dry and fire the bricks or shapes)
40 CFR 63.8530 through 40 CFR 63.8665
(facilities that manufacture pressed floor tile, pressed wall tile, other pressed tile, or sanitaryware, and typically process clay, shale, and various additives, form the processed materials into tile or sanitaryware shapes, and dry and fire the ceramic products)
40 CFR 63.8680 through 40 CFR 63.8698
(preparation of asphalt flux at stand-alone asphalt processing facilities, petroleum refineries, and asphalt roofing facilities)
40 CFR 63.8780 through 40 CFR 63.8830
(flexible polyurethane foam fabrication plants using flame lamination or loop slitter adhesives)
40 CFR 63.8980 through 40 CFR 63.9075
(HCl production facilities that produce a liquid HCl product)
40 CFR Subpart 63.9280 through 40 CFR 63.9375
(any apparatus used for testing uninstalled stationary or uninstalled mobile (motive) engines)
40 CFR 63.9480 through 40 CFR 63.9579
(friction materials manufacturing facilities that use a solvent-based process)
40 CFR 63.9580 through 40 CFR 63.9652
(ore crushing and handling, ore dryer stacks, indurating furnace stacks, finished pellet handling, and fugitive dust)
40 CFR 63.9780 through 40 CFR 63.9824
(manufacture of refractory products, including refractory bricks and shapes, monolithics, kiln furniture, crucibles, and other materials for liming furnaces and other high temperature process units)
40 CFR 63.9880 through 40 CFR 63.9942
(spray dryer, magnesium chloride storage bin scrubber, melt/reactor system, and launder off-gas system stacks)
40 CFR 63.9980 through 40 CFR 63.10042
(any furnace, boiler, or other device used for combusting fuel for the purpose of producing steam, including fossil fuel-fired steam generators associated with integrated gasification combined cycle gas turbines and excluding nuclear steam generators, for the purpose of powering a generator to produce electricity or electricity and other thermal energy)
40 CFR 63.10382 through 40 CFR 63.10448
(any enclosed vessel that is filled with ethylene oxide gas or an ethylene oxide/inert gas mixture for the purpose of sterilization)
40 CFR 63.10680 through 40 CFR 63.10692
(a steel plant that produces carbon, alloy, or specialty steels using an electric arc furnace)
40 CFR 63.10880 through 40 CFR 63.10906
(a facility that melts scrap, ingot, and/or other forms of iron and/or steel and pours the resulting molten metal into molds to produce final or near final shape products for introduction into commerce)
40 CFR 63.11080 through 40 CFR 63.11100
(gasoline storage tanks, gasoline loading racks, vapor collection-equipped gasoline cargo tanks, and equipment components in vapor or liquid gasoline service)
40 CFR 63.11110 through 40 CFR 63.11132
(NOTE: Authority to enforce the above standard is being retained by EPA and it is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)
40 CFR 63.11140 through 40 CFR 63.11145
(plants that produce polyvinyl chloride or copolymers)
40 CFR 63.11146 through 40 CFR 63.11152
(any installation or any intermediate process engaged in the production of copper from copper sulfide ore concentrates through the use of pyrometallurgical techniques)
40 CFR 63.11153 through 40 CFR 63.11159
(a facility that processes copper scrap in a blast furnace and converter or that uses another pyrometallurgical purification process to produce anode copper from copper scrap, including low-grade copper scrap)
40 CFR 63.11160 through 40 CFR 63.11168
(cadmium melting furnaces used to melt cadmium or produce cadmium oxide from the cadmium recovered in the zinc production; primary beryllium production facilities engaged in the chemical processing of beryllium ore to produce beryllium metal, alloy, or oxide, or performing any of the intermediate steps in these processes; and primary zinc production facilities engaged in the production, or any intermediate process in the production, of zinc or zinc oxide from zinc sulfide ore concentrates through the use of pyrometallurgical techniques)
40 CFR 63.11169 through 40 CFR 63.11180
(NOTE: Authority to enforce the above standard is being retained by EPA and it is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)
40 CFR 63.11193 through 40 CFR 63.11226
(NOTE: Authority to enforce the above standard is being retained by EPA and is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)
40 CFR 63.11393 through 40 CFR 63.11399
(production of either of the following synthetic fibers composed of acrylonitrile units: acrylic fiber or modacrylic fiber)
40 CFR 63.11400 through 40 CFR 63.11406
(carbon black production process units including all waste management units, maintenance wastewater, and equipment components that contain or contact HAP that are associated with the carbon black production process unit)
40 CFR 63.11407 through 40 CFR 63.11413
(any process that uses chromite ore as the basic feedstock to manufacture chromium compounds, primarily sodium dichromate, chromic acid, and chromic oxide)
40 CFR 63.11414 through 40 CFR 63.11420
(a facility where pieces of flexible polyurethane foam are cut, bonded, and/or laminated together or to other substrates)
40 CFR 63.11421 through 40 CFR 63.11427
(grid casting facilities, paste mixing facilities, three-process operation facilities, lead oxide manufacturing facilities, lead reclamation facilities, and any other lead-emitting operation that is associated with the lead acid battery manufacturing plant)
40 CFR 63.11428 through 40 CFR 63.11434
(pressure or thermal impregnation of chemicals into wood to provide effective long-term resistance to attack by fungi, bacteria, insects, and marine borers)
40 CFR 63.11435 through 40 CFR 63.11447
(manufacture of pressed tile, sanitaryware, dinnerware, or pottery with an atomized glaze spray booth or kiln that fires glazed ceramic ware)
40 CFR 63.11448 through 40 CFR 63.11461
(manufacture of flat glass, glass containers, or pressed and blown glass by melting a mixture of raw materials to produce molten glass and form the molten glass into sheets, containers, or other shapes)
40 CFR 63.11462 through 40 CFR 63.11474
(all crushing and screening operations at a secondary zinc processing facility and all furnace melting operations located at any secondary nonferrous metals processing facility)
40 CFR 63.11494 through 40 CFR 11503
(each chemical manufacturing process unit that uses as feedstocks, generates as byproducts, or produces as products any of the following: 1,3-butadiene; 1,3-dichloropropene; acetaldehyde; chloroform; ethylene dichloride; methylene chloride; hexachlorobenzene; hydrazine; quinoline; or compounds of arsenic, cadmium, chromium, lead, manganese, or nickel)
40 CFR 63.11504 through 40 CFR 63.11513
(new and existing tanks, thermal spraying equipment, and mechanical polishing equipment used in non-chromium electroplating, electroless or non-electrolytic plating, non-electrolytic metal coating, dry mechanical polishing, electroforming, and electropolishing)
40 CFR 63.11514 through 40 CFR 63.11523
(NOTE: Authority to enforce the above standard is being retained by EPA and it is not incorporated by reference into these regulations for any source that is not (i) a major source as defined in 9VAC5-80-60 and subject to Article 1 (9VAC5-80-50 et seq., Federal Operating Permits for Stationary Sources) of Part II of 9VAC5-80 (Permits for Stationary Sources) or (ii) an affected source as defined in 9VAC5-80-370 and subject to Article 3 (9VAC5-80-360 et seq., Federal Operating Permits for Acid Rain Sources) of Part II of 9VAC5-80.)
40 CFR 63.11524 through 40 CFR 63.11543
(manufacture of silicon metal, ferrosilicon, ferrotitanium using the aluminum reduction process, ferrovanadium, ferromolybdenum, calcium silicon, silicomanganese zirconium, ferrochrome silicon, silvery iron, high-carbon ferrochrome, charge chrome, standard ferromanganese, silicomanganese, ferromanganese silicon, calcium carbide or other ferroalloy products using electrometallurgical operations including electric arc furnaces or other reaction vessels)
40 CFR 63.11544 through 40 CFR 63.11558
(melting operations at aluminum, copper, and other nonferrous foundries, including the collection of induction, reverberatory, crucible, tower, or dry hearth furnaces used to melt metal ingot, alloyed ingot and/or metal scrap to produce molten metal that is poured into molds to make castings)
40 CFR 63.11559 through 40 CFR 63.11567
(asphalt processing operations that prepare asphalt flux at standalone asphalt processing facilities, petroleum refineries, and asphalt roofing facilities that include one or more asphalt flux blowing stills; and asphalt roofing manufacturing operations that manufacture asphalt roofing products through a series of sequential process steps depending upon whether the type of substrate used is organic or inorganic)
40 CFR 63.11579 through 40 CFR 63.11588
(any facility-wide collection of chemical preparation operations, including the collection of mixing, blending, milling, and extruding equipment used to manufacture chemical preparations that contain metal compounds for chromium, lead, manganese, and nickel)
40 CFR 63.11599 through 40 CFR 63.11638
(paints and allied products manufacturing processes, including, weighing, blending, mixing, grinding, tinting, dilution or other formulation, as well as cleaning operations, material storage and transfer, and piping)
40 CFR 63.11619 through 40 CFR 63.11638
(production of animal feed from the point in the process where a material containing chromium or manganese is added, to the point where the finished product leaves the facility, including areas where materials containing chromium and manganese are stored, areas where materials containing chromium and manganese are temporarily stored prior to addition to the feed at the mixer, mixing and grinding processes, pelleting and pellet cooling processes, packing and bagging processes, crumblers and screens, bulk loading operations, and all conveyors and other equipment that transfer feed materials)
40 CFR 63.11640 through 40 CFR 63.11653
(any industrial facility engaged in the processing of gold mine ore that uses any of the following processes: roasting operations, autoclaves, carbon kilns, preg tanks, electrowinning, mercury retorts, or melt furnaces)
40 CFR 63.11860 through 40 CFR 63.12000
(facility-wide collection of PVCPU, storage vessels, heat exchange systems, surge control vessels, wastewater and process wastewater treatment systems that are associated with producing polyvinyl chloride and copolymers)
Appendix A - Test Methods.
Appendix B - Sources Defined for Early Reduction Provisions.
Appendix C - Determination of the Fraction Biodegraded (Fbio) in a Biological Treatment Unit.
Appendix D - Alternative Validation Procedure for EPA Waste and Wastewater Methods.
9 Va. Admin. Code § 5-60-100
Statutory Authority: 10.1-1308 of the Code of Virginia; §§ 110, 111, 123, 129, 171, 172, and 182 of the Clean Air Act; 40 CFR Parts 51 and 60