Section R309-210-9 - Disinfection Byproducts - Initial Distribution System Evaluations(1) General requirements. (a) The requirements of this sub-section establish monitoring and other requirements for identifying R309-210-10 compliance monitoring locations for determining compliance with maximum contaminant levels for total trihalomethanes (TTHM) and haloacetic acids (five)(HAA5). The water system must use an Initial Distribution System Evaluation (IDSE) to determine locations with representative high TTHM and HAA5 concentrations throughout the distribution system. IDSEs are used in conjunction with, but separate from, R309-210-8 compliance monitoring, to identify and select R309-210-10 compliance monitoring locations.(b) Applicability. Community water systems that uses a primary or residual disinfectant other than ultraviolet light or delivers water that has been treated with a primary or residual disinfectant other than ultraviolet light; or if the system is a non-transient non-community water systems that serves at least 10,000 people and uses a primary or residual disinfectant other than ultraviolet light or delivers water that has been treated with a primary or residual disinfectant other than ultraviolet light are subject to these requirements.(c) Schedule. The water system must comply with the requirements of this subpart on the schedule in paragraph (c)(i). (i) For water systems that are not part of a combined distribution system and systems that serve the largest population in the combined distribution system. (A) For water systems that serve a population greater than or equal to 100,000: (I) The water system must submit a standard monitoring plan or system specific study plan or 40/30 certification to the Director by or receive very small system waiver from the Director by October 1, 2006.(II) The water system must complete the standard monitoring or system specific study by September 30, 2008.(III) The water system must submit the IDSE report to the Director by January 1, 2009.(B) For water systems that serve a population from 50,000 to 99,999: (I) The water system must submit a standard monitoring plan or system specific study plan or 40/30 certification to the Director by or receive very small system waiver from the Director by April 1, 2007.(II) The water system must complete the standard monitoring or system specific study by March 31, 2009.(III) The water system must submit the IDSE report to the Director by July 1, 2009.(C) For water systems that serve a population from 10,000 to 49,999: (I) The water system must submit a standard monitoring plan or system specific study plan or 40/30 certification to the Director by or receive very small system waiver from the Director by October 1, 2007.(II) The water system must complete the standard monitoring or system specific study by September 30, 2009.(III) The water system must submit the IDSE report to the Director by January 1, 2010.(D) For community water systems that serve a population less than 10,000: (I) The water system must submit a standard monitoring plan or system specific study plan or 40/30 certification to the Director by or receive very small system waiver from the Director by April 1, 2008.(II) The water system must complete the standard monitoring or system specific study by March 31, 2010.(III) The water system must submit the IDSE report to the Director by July 1, 2010.(ii) For other water systems that are part of a combined distribution system: (A) For wholesale systems or consecutive systems: (I) The water system must submit a standard monitoring plan or system specific study plan or 40/30 certification to the Director by or receive very small system waiver from the Director at the same time as the system with the earliest compliance date in the combined distribution system.(II) The water system must complete the standard monitoring or system specific study at the same time as the system with the earliest compliance date in the combined distribution system.(III) The water system must submit the IDSE report to the Director by at the same time as the system with the earliest compliance date in the combined distribution system.(iii) If, within 12 months after the date the water system is required to submit the information in (i)(A)(I), (B)(I), (C)(I), (D)(I) and (ii)(A)(I) above, the Director does not approve the water system plan or notify the water system that it has not yet completed its review, the water system may consider the plan that was submitted as approved. The water system must implement that plan and must complete standard monitoring or a system specific study no later than the date identified in (i)(A)(II), (B)(II), (C)(II), (D)(II) and (ii)(A)(II) above.(iv) The water system must submit the 40/30 certification under R309-210-9(4) by the date identified in (i)(A)(II), (B)(II), (C)(II), (D)(II) and (ii)(A)(II) above.(v) If, within three months after the date identified in (i)(A)(III), (B)(III), (C)(III), (D)(III) and (ii)(A)(III) above (nine months after the date identified in this column if the water system must comply on the schedule in paragraph (c)(i)(C) of this section), the Director does not approve the IDSE report or notify the water system that it has not yet completed its review, the water system may consider the report submitted as approved and must implement the recommended R309-210-10 monitoring as required.(vi) For the purpose of the schedule in paragraph (c)(i) through (c)(v) of this section, the Director may determine that the combined distribution system does not include certain consecutive systems based on factors such as receiving water from a wholesale system only on an emergency basis or receiving only a small percentage and small volume of water from a wholesale system. The Director may also determine that the combined distribution system does not include certain wholesale systems based on factors such as delivering water to a consecutive system only on an emergency basis or delivering only a small percentage and small volume of water to a consecutive system.(d) The water system must conduct standard monitoring that meets the requirements in R309-210-9(2), or a system specific study that meets the requirements in R309-210-9(3), or certify to the Director that the water system meet 40/30 certification criteria under R309-210-9(4), or qualify for a very small system waiver under R309-210-9(5). (i) The water system must have taken the full complement of routine TTHM and HAA5 compliance samples required of a system with the population and source water under R309-210-8 (or the water system must have taken the full complement of reduced TTHM and HAA5 compliance samples required of a system with the population and source water under R309-210-8 if the water system meets reduced monitoring criteria under R309-210-8) during the period specified in R309-210-9(4)(a) to meet the 40/ 30 certification criteria in R309-210-9(4) the water system must have taken TTHM and HAA5 samples under R309-200-4(3) and R309-210-8 to be eligible for the very small system waiver in R309-210-9(5).(ii) If the water system has not taken the required samples, the water system must conduct standard monitoring that meets the requirements in R309-210-9(2), or a system specific study that meets the requirements in R309-210-9(3).(e) The water system must use only the analytical methods specified in R309-200-4(3), or otherwise approved by EPA for monitoring under this subpart, to demonstrate compliance with the requirements of this subpart.(f) IDSE results will not be used for the purpose of determining compliance with MCLs in R309-200-5(3)(c).(2) Standard monitoring. (a) Standard monitoring plan. The standard monitoring plan must comply with paragraphs (a)(i) through (a)(iv) of this section. The water system must prepare and submit the standard monitoring plan to the Director according to the schedule in R309-210-9(1)(c). (i) The standard monitoring plan must include a schematic of the distribution system (including distribution system entry points and their sources, and storage facilities), with notes indicating locations and dates of all projected standard monitoring, and all projected R309-210-8 compliance monitoring.(ii) The standard monitoring plan must include justification of standard monitoring location selection and a summary of data the water system relied on to justify standard monitoring location selection.(iii) The standard monitoring plan must specify the population served and system type (surface water or ground water).(iv) The water system must retain a complete copy of the standard monitoring plan submitted under this paragraph (a), including any Director modification of the standard monitoring plan, for as long as the water system is required to retain the IDSE report under R309-105-17(8).(b) Standard monitoring. (i) The water system must monitor as indicated in paragraph (b)(i). The water system must collect dual sample sets at each monitoring location. One sample in the dual sample set must be analyzed for TTHM. The other sample in the dual sample set must be analyzed for HAA5. The water system must conduct one monitoring period during the peak historical month for TTHM levels or HAA5 levels or the month of warmest water temperature. The water system must review available compliance, study, or operational data to determine the peak historical month for TTHM or HAA5 levels or warmest water temperature. (A) Surface water systems serving less than 500 population which are consecutive systems. (I) One monitoring period per year, dual sample sets must be taken during the peak historical month. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken near the entry point of the disinfected water into the distribution system.(B) Surface water systems serving less than 500 population which are non-consecutive systems. (I) One monitoring period per year, dual sample sets must be taken during the peak historical month. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken at the high HAA5 location in the distribution system.(C) Surface water systems serving between 500 to 3,300 population which are consecutive systems. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken near the entry point of the disinfected water into the distribution system.(D) Surface water systems serving between 500 to 3,300 population which are non-consecutive systems. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken at the high HAA5 location in the distribution system.(E) Surface water systems serving between 3,301 to 9,999 population. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Four dual samples sets must be collected per monitoring period.(II) Two dual sample sets must be taken at the high TTHM locations in the distribution system.(III) One dual sample set must be taken at the high HAA5 location in the distribution system.(IV) One dual sample set must be taken at an average residence time of the disinfected water in the distribution system.(F) Surface water systems serving between 10,000 to 49,999 population. (I) Six monitoring periods per year, dual sample sets must be taken every 60 days. Eight dual samples sets must be collected per monitoring period.(II) Three dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Two dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) Two dual sample sets must be taken at an average residence time of the disinfected water in the distribution system.(V) One dual sample set must be taken near the entry point of the disinfected water into the distribution system.(G) Surface water systems serving between 50,000 to 249,999 population. (I) Six monitoring periods per year, dual sample sets must be taken every 60 days. 16 dual samples sets must be collected per monitoring period.(II) Five dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Four dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) Four dual sample sets must be taken at an average residence time of the disinfected water in the distribution system.(V) Three dual sample sets must be taken near the entry point of the disinfected water into the distribution system.(H) Surface water systems serving between 250,000 to 999,999 population. (I) Six monitoring periods per year, dual sample sets must be taken every 60 days. 24 dual samples sets must be collected per monitoring period.(II) Eight dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Six dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) Six dual sample sets must be taken at an average residence time of the disinfected water in the distribution system.(V) Four dual sample sets must be taken near the entry point of the disinfected water into the distribution system.(I) Surface water systems serving between 1,000,000 to 4,999,999 population. (I) Six monitoring periods per year, dual sample sets must be taken every 60 days. 32 dual samples sets must be collected per monitoring period.(II) Ten dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Eight dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) Eight dual sample sets must be taken at an average residence time of the disinfected water in the distribution system.(V) Six dual sample sets must be taken near the entry point of the disinfected water into the distribution system.(J) Surface water systems serving 5,000,000 or more population. (I) Six monitoring periods per year, dual sample sets must be taken every 60 days. 40 dual samples sets must be collected per monitoring period.(II) Twelve dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Ten dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) Ten dual sample sets must be taken at an average residence time of the disinfected water in the distribution system.(V) Eight dual sample sets must be taken near the entry point of the disinfected water into the distribution system.(K) Ground water systems serving less than 500 population which are consecutive systems. (I) One monitoring period per year, dual sample sets must be taken during the peak historical month. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken near the entry point of the disinfected water into the distribution system.(L) Ground water systems serving less than 500 population which are non-consecutive systems. (I) One monitoring period per year, dual sample sets must be taken during the peak historical month. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken at the high HAA5 location in the distribution system.(M) Ground water systems serving between 500 to 9,999 population. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Two dual samples sets must be collected per monitoring period.(II) One dual sample set must be taken at the high TTHM location in the distribution system.(III) One dual sample set must be taken at the high HAA5 location in the distribution system.(N) Ground water systems serving between 10,000 to 99,999 population. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Six dual samples sets must be collected per monitoring period.(II) Two dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Two dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) One dual sample set must be taken at an average residence time of the disinfected water in the distribution system.(V) One dual sample set must be taken near the entry point of the disinfected water into the distribution system.(O) Ground water systems serving between 100,000 to 499,999 population. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Eight dual samples sets must be collected per monitoring period.(II) Three dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Three dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) One dual sample set must be taken at an average residence time of the disinfected water in the distribution system.(V) One dual sample set must be taken near the entry point of the disinfected water into the distribution system.(P) Ground water systems serving 500,000 or greater population. (I) Four monitoring periods per year, dual sample sets must be taken every 90 days. Twelve dual samples sets must be collected per monitoring period.(II) Four dual sample sets must be taken at the high TTHM locations in the distribution system.(III) Four dual sample sets must be taken at the high HAA5 locations in the distribution system.(IV) Two dual sample sets must be taken at an average residence time of the disinfected water in the distribution system.(V) Two dual sample sets must be taken near the entry point of the disinfected water into the distribution system.(Q) A dual sample set (i.e., a TTHM and an HAA5 sample) must be taken at each monitoring location during each monitoring period.(R) The peak historical month is the month with the highest TTHM or HAA5 levels or the warmest water temperature.(ii) The water system must take samples at locations other than the existing R309-210-8 monitoring locations. Monitoring locations must be distributed throughout the distribution system.(iii) If the number of entry points to the distribution system is fewer than the specified number of entry point monitoring locations, excess entry point samples must be replaced equally at high TTHM and HAA5 locations. If there is an odd extra location number, the water system must take a sample at a high TTHM location. If the number of entry points to the distribution system is more than the specified number of entry point monitoring locations, the water system must take samples at entry points to the distribution system having the highest annual water flows.(iv) The system monitoring under this paragraph (b) may not be reduced under the provisions of R309-105-5(2).(c) IDSE report. The IDSE report must include the elements required in paragraphs (c)(i) through (c)(iv) of this section. The water system must submit the IDSE report to the Director according to the schedule in R309-210-9(1)(c). (i) The IDSE report must include all TTHM and HAA5 analytical results from R309-210-8 compliance monitoring and all standard monitoring conducted during the period of the IDSE as individual analytical results and LRAAs presented in a tabular or spreadsheet format acceptable to the Director. If changed from the standard monitoring plan submitted under paragraph (a) of this section, the report must also include a schematic of the distribution system, the population served, and system type (surface water or ground water).(ii) The IDSE report must include an explanation of any deviations from the approved standard monitoring plan.(iii) The water system must recommend and justify R309-210-10 compliance monitoring locations and timing based on the protocol in R309-210-9(6).(iv) The water system must retain a complete copy of the IDSE report submitted under this section for 10 years after the date that the water system submitted the report. If the Director modifies the R309-210-10 monitoring requirements that the water system recommended in the IDSE report or if the Director approves alternative monitoring locations, the water system must keep a copy of the Director's notification on file for 10 years after the date of the Director's notification. The water system must make the IDSE report and any Director notification available for review by the Director or the public.(3) System specific studies. (a) System specific study plan. The water system specific study plan must be based on either existing monitoring results as required under paragraph (a)(i) of this section or modeling as required under paragraph (a)(ii) of this section. The water system must prepare and submit the system specific study plan to the Director according to the schedule in R309-210-9(1)(c). (i) Existing monitoring results. The water system may comply by submitting monitoring results collected before the water system is required to begin monitoring under R309-210-9(1)(c). The monitoring results and analysis must meet the criteria in paragraphs (a)(i)(A) and (a)(i)(B) of this section. (A) Minimum requirements. (I) TTHM and HAA5 results must be based on samples collected and analyzed in accordance with R309-200-4(3). Samples must be collected no earlier than five years prior to the study plan submission date.(II) The monitoring locations and frequency must meet the conditions identified in this paragraph (a)(i)(A)(II). Each location must be sampled once during the peak historical month for TTHM levels or HAA5 levels or the month of warmest water temperature for every 12 months of data submitted for that location. Monitoring results must include all R309-210-8 compliance monitoring results plus additional monitoring results as necessary to meet minimum sample requirements.(III) Surface water systems serving a population less than 500 shall have data from: (aa) three monitoring locations; and(bb) three samples for each TTHM and HAA5. (IV) Surface water systems serving a population between 500 to 3,300 shall have data from: (aa) three monitoring locations; and(bb) nine samples each for TTHM and HAA5.(V) Surface water systems serving a population between 3,301 to 9,999 shall have data from: (aa) six monitoring locations; and(bb) 36 samples each for TTHM and HAA5.(VI) Surface water systems serving a population between 10,000 to 49,999 shall have data from: (aa) 12 monitoring locations; and(bb) 72 samples each for TTHM and HAA5.(VII) Surface water systems serving a population between 50,000 to 249,999 shall have data from: (aa) 24 monitoring locations; and(bb) 144 samples each for TTHM and HAA5.(VIII) Surface water systems serving a population between 250,000 to 999,999 shall have data from: (aa) 36 monitoring locations; and(bb) 216 samples each for TTHM and HAA5.(IX) Surface water systems serving a population between 1,000,000 to 4,999,999 shall have data from: (aa) 48 monitoring locations; and(bb) 288 samples each for TTHM and HAA5.(X) Surface water systems serving a population 5,000,000 or greater shall have data from: (aa) 60 monitoring locations; and(bb) 360 samples each for TTHM and HAA5.(XI) Ground water systems serving a population less than 500 shall have data from: (aa) three monitoring locations; and(bb) three samples for each TTHM and HAA5.(XII) Ground water systems serving a population between 500 to 9,999 shall have data from: (aa) three monitoring locations; and(bb) nine samples each for TTHM and HAA5.(XIII) Ground water systems serving a population between 10,000 to 99,999 shall have data from: (aa) 12 monitoring locations; and(bb) 48 samples each for TTHM and HAA5.(XIV) Ground water systems serving a population between 100,000 to 499,999 shall have data from: (aa) 18 monitoring locations; and(bb) 72 samples each for TTHM and HAA5.(XV) Ground water systems serving a population of 500,000 or greater shall have data from: (aa) 24 monitoring locations; and(bb) 96 samples each for TTHM and HAA5. (B) Reporting monitoring results. The water system must report the information in this paragraph (a)(i)(B). (I) The water system must report previously collected monitoring results and certify that the reported monitoring results include all compliance and non-compliance results generated during the time period beginning with the first reported result and ending with the most recent R309-210-8 results.(II) The water system must certify that the samples were representative of the entire distribution system and that treatment, and distribution system have not changed significantly since the samples were collected.(III) The study monitoring plan must include a schematic of the distribution system (including distribution system entry points and their sources, and storage facilities), with notes indicating the locations and dates of all completed or planned system specific study monitoring.(IV) The water system specific study plan must specify the population served and system type (surface water or ground water).(V) The water system must retain a complete copy of the system specific study plan submitted under this paragraph (a)(i), including any Director modification of the system specific study plan, for as long as the water system is required to retain the IDSE report under paragraph (b)(v) of this section.(VI) If the water system submits previously collected data that fully meet the number of samples required under paragraph (a)(i)(A)(II) of this section and the Director rejects some of the data, the water system must either conduct additional monitoring to replace rejected data on a schedule the Director approves or conduct standard monitoring under R309-210-9(2). (ii) Modeling. The water system may comply through analysis of an extended period simulation hydraulic model. The extended period simulation hydraulic model and analysis must meet the criteria in this paragraph (a)(ii). (A) Minimum requirements. (I) The model must simulate 24 hour variation in demand and show a consistently repeating 24 hour pattern of residence time.(II) The model must represent the criteria listed in paragraphs (a)(ii)(A)(II)(aa) through (ii) of this section. (dd) All 12-inch diameter and larger pipes;(ee) All 8-inch and larger pipes that connect pressure zones, influence zones from different sources, storage facilities, major demand areas, pumps, and control valves, or are known or expected to be significant conveyors of water;(ff) All 6-inch and larger pipes that connect remote areas of a distribution system to the main portion of the system;(gg) All storage facilities with standard operations represented in the model; and(hh) All active pump stations with controls represented in the model; and(ii) All active control valves.(III) The model must be calibrated, or have calibration plans, for the current configuration of the distribution system during the period of high TTHM formation potential. All storage facilities must be evaluated as part of the calibration process. All required calibration must be completed no later than 12 months after plan submission.(B) Reporting modeling. The system specific study plan must include the information in this paragraph (a)(ii)(B). (I) Tabular or spreadsheet data demonstrating that the model meets requirements in paragraph (a)(ii)(A)(II) of this section.(II) A description of all calibration activities undertaken, and if calibration is complete, a graph of predicted tank levels versus measured tank levels for the storage facility with the highest residence time in each pressure zone, and a time series graph of the residence time at the longest residence time storage facility in the distribution system showing the predictions for the entire simulation period (i.e., from time zero until the time it takes to for the model to reach a consistently repeating pattern of residence time).(III) Model output showing preliminary 24 hour average residence time predictions throughout the distribution system.(IV) Timing and number of samples representative of the distribution system planned for at least one monitoring period of TTHM and HAA5 dual sample monitoring at a number of locations no less than would be required for the system under standard monitoring in R309-210-9(2) during the historical month of high TTHM. These samples must be taken at locations other than existing R309-210-8 compliance monitoring locations.(V) Description of how all requirements will be completed no later than 12 months after the water system submits the system specific study plan.(VI) Schematic of the distribution system (including distribution system entry points and their sources, and storage facilities), with notes indicating the locations and dates of all completed system specific study monitoring (if calibration is complete) and all R309-210-8 compliance monitoring.(VII) Population served and system type (surface water or ground water).(VIII) The water system must retain a complete copy of the system specific study plan submitted under this paragraph (a)(ii), including any Director modification of the system specific study plan, for as long as the water system is required to retain the IDSE report under paragraph (b)(vii) of this section.(C) If the water system submits a model that does not fully meet the requirements under paragraph (a)(ii) of this section, the water system must correct the deficiencies and respond to Director inquiries concerning the model. If the water system fails to correct deficiencies or respond to inquiries to the Director's satisfaction, the water system must conduct standard monitoring under R309-210-9(2).(b) IDSE report. The IDSE report must include the elements required in paragraphs (b)(i) through (b)(vi) of this section. The water system must submit the IDSE report according to the schedule in R309-210-9(1)(c). (i) The IDSE report must include all TTHM and HAA5 analytical results from R309-210-8 compliance monitoring and all system specific study monitoring conducted during the period of the system specific study presented in a tabular or spreadsheet format acceptable to the Director. If changed from the system specific study plan submitted under paragraph (a) of this section, the IDSE report must also include a schematic of the distribution system, the population served, and system type (surface water or ground water).(ii) If the water system used the modeling provision under paragraph (a)(ii) of this section, the water system must include final information for the elements described in paragraph (a)(ii)(B) of this section, and a 24- hour time series graph of residence time for each R309-210-10 compliance monitoring location selected.(iii) The water system must recommend and justify R309-210-10 compliance monitoring locations and timing based on the protocol in R309-210-9(6).(iv) The IDSE report must include an explanation of any deviations from the approved system specific study plan.(v) The IDSE report must include the basis (analytical and modeling results) and justification the water system used to select the recommended R309-210-10 monitoring locations.(vi) The water system may submit the IDSE report in lieu of the system specific study plan on the schedule identified in R309-210-9(1) (c) for submission of the system specific study plan if the water system believes that it has the necessary information by the time that the system specific study plan is due. If the water system elects this approach, the IDSE report must also include all information required under paragraph (a) of this section.(vii) The water system must retain a complete copy of the IDSE report submitted under this section for 10 years after the date the water system submitted the IDSE report. If the Director modifies the R309-210-10 monitoring requirements the water system recommended in the IDSE report or if the Director approves alternative monitoring locations, the water system must keep a copy of the Director's notification on file for 10 years after the date of the Director's notification. The water system must make the IDSE report and any Director notification available for review by the Director or the public.(4) 40/30 certification. (a) Eligibility. The water system is eligible for 40/ 30 certification if it had no TTHM or HAA5 monitoring violations under R309-210-8 of this part and no individual sample exceeded 0.040 mg/L for TTHM or 0.030 mg/L for HAA5 during an eight consecutive calendar quarter period beginning no earlier than the date specified in this paragraph (a). (i) If the 40/30 certification is due October 1, 2006 then the eligibility for 40/30 certification is based on eight consecutive calendar quarters of R309-210-8 compliance monitoring results beginning no earlier than January 2004.(ii) If the 40/30 certification is due April 1, 2007 then the eligibility for 40/30 certification is based on eight consecutive calendar quarters of R309-210-8 compliance monitoring results beginning no earlier than January 2004.(iii) If the 40/30 certification is due October 1, 2007 then the eligibility for 40/30 certification is based on eight consecutive calendar quarters of R309-210-8 compliance monitoring results beginning no earlier than January 2005.(iv) If the 40/30 certification is due April 1, 2008 then the eligibility for 40/30 certification is based on eight consecutive calendar quarters of R309-210-8 compliance monitoring results beginning no earlier than January 2005.(v) Unless the water system is on reduced monitoring under R309-210-8 of this part and were not required to monitor during the specified period. If the water system did not monitor during the specified period, the water system must base its eligibility on compliance samples taken during the 12 months preceding the specified period.(b) 40/30 certification. (i) The water system must certify to the Director that every individual compliance sample taken under R309-210-8 of this part during the periods specified in paragraph (a) of this section were less than or equal to 0.040 mg/L for TTHM and less than or equal to 0.030 mg/L for HAA5, and that the water system did not have any TTHM or HAA5 monitoring violations during the period specified in paragraph (a) of this section.(ii) The Director may require the water system to submit compliance monitoring results, distribution system schematics, and/or recommended R309-210-10 compliance monitoring locations in addition to the certification. If the water system fails to submit the requested information, the Director may require standard monitoring under R309-210-9(2) or a system specific study under R309-210-9(3).(iii) The Director may still require standard monitoring under R309-210-9(2) or a system specific study under R309-210-9(3) even if the water system meets the criteria in paragraph (a) of this section.(iv) A water system must retain a complete copy of its certification submitted under this section for 10 years after the date that the water system submitted the certification. The water system must make the certification, all data upon which the certification is based, and any Director notification available for review by the Director or the public.(5) Very small system waivers. (a) If the water system serves fewer than 500 people and it has taken TTHM and HAA5 samples under R309-210-8, the water system is not required to comply with this subpart unless the Director notifies the water system that it must conduct standard monitoring under R309-210-9(2) or a system specific study under R309-210-9(3).(b) If the water system has not taken TTHM and HAA5 samples under R309-210-8 or if the Director notifies the water system that the water system must comply with this subpart, the water system must conduct standard monitoring under R309-210-9(2) or a system specific study under R309-210-9(3).(6) Stage 2 (R309-210-10) compliance monitoring location recommendations. (a) The IDSE report must include the recommendations and justification for where and during what month(s) TTHM and HAA5 monitoring for R309-210-10 of this part should be conducted. The water system must base the recommendations on the criteria in paragraphs (b) through (e) of this section.(b) The water system must select the number of monitoring locations specified in this paragraph (b). The water system will use these recommended locations as R309-210-10 routine compliance monitoring locations, unless Director requires different or additional locations. The water system should distribute locations throughout the distribution system to the extent possible. (i) Surface water systems serving less than 500. (A) One monitoring period per year. Two dual samples sets must be collected per monitoring period.(B) One dual sample set must be taken at the high TTHM location in the distribution system.(C) One dual sample set must be taken at the high HAA5 location in the distribution system.(ii) Surface water systems serving between 500 to 3,300. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Two dual samples sets must be collected per monitoring period.(B) One dual sample set must be taken at the high TTHM location in the distribution system.(C) One dual sample set must be taken at the high HAA5 location in the distribution system.(iii) Surface water systems serving between 3,301 to 9,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Two dual samples sets must be collected per monitoring period.(B) One dual sample set must be taken at the high TTHM locations in the distribution system.(C) One dual sample set must be taken at the high HAA5 location in the distribution system.(iv) Surface water systems serving between 10,000 to 49,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Four dual samples sets must be collected per monitoring period.(B) Two dual sample sets must be taken at the high TTHM locations in the distribution system.(C) One dual sample set must be taken at the high HAA5 locations in the distribution system.(D) One dual sample set must be taken at an existing R309-210-8 compliance location.(v) Surface water systems serving between 50,000 to 249,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Eight dual samples sets must be collected per monitoring period.(B) Three dual sample sets must be taken at the high TTHM locations in the distribution system.(C) Three dual sample sets must be taken at the high HAA5 locations in the distribution system.(D) Two dual samples sets must be taken at an existing R309-210-8 compliance location.(vi) Surface water systems serving between 250,000 to 999,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. 12 dual samples sets must be collected per monitoring period.(B) Five dual sample sets must be taken at the high TTHM locations in the distribution system.(C) Four dual sample sets must be taken at the high HAA5 locations in the distribution system.(D) Three dual sample sets must be taken at an existing R309-210-8 compliance location.(vii) Surface water systems serving between 1,000,000 to 4,999,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. 16 dual samples sets must be collected per monitoring period.(B) Six dual sample sets must be taken at the high TTHM locations in the distribution system.(C) Six dual sample sets must be taken at the high HAA5 locations in the distribution system.(D) Four dual sample sets must be taken at an existing R309-210-8 compliance location.(viii) Surface water systems serving 5,000,000 or more population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. 20 dual samples sets must be collected per monitoring period.(B) Eight dual sample sets must be taken at the high TTHM locations in the distribution system.(C) Seven dual sample sets must be taken at the high HAA5 locations in the distribution system.(D) Five dual sample sets must be taken at an existing R309-210-8 compliance location.(ix) Ground water systems serving less than 500. (A) One monitoring period per year. Two dual samples sets must be collected per monitoring period.(B) One dual sample set must be taken at the high TTHM location in the distribution system.(C) One dual sample set must be taken at the high HAA5 location in the distribution system.(x) Ground water systems serving between 500 to 9,999 population. (A) One monitoring period per year. Two dual samples sets must be collected per monitoring period.(B) One dual sample set must be taken at the high TTHM location in the distribution system.(C) One dual sample set must be taken at the high HAA5 location in the distribution system.(xi) Ground water systems serving between 10,000 to 99,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Four dual samples sets must be collected per monitoring period.(B) Two dual sample sets must be taken at the high TTHM locations in the distribution system.(C) One dual sample set must be taken at the high HAA5 locations in the distribution system.(D) One dual sample set must be taken at an existing R309-210-8 compliance location.(xii) Ground water systems serving between 100,000 to 499,999 population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Six dual samples sets must be collected per monitoring period.(B) Three dual sample sets must be taken at the high TTHM locations in the distribution system.(C) Two dual sample sets must be taken at the high HAA5 locations in the distribution system.(D) One dual sample set must be taken at an existing R309-210-8 compliance location.(xiii) Ground water systems serving 500,000 or greater population. (A) Four monitoring periods per year, dual sample sets must be taken every 90 days. Eight dual samples sets must be collected per monitoring period.(B) Three dual sample sets must be taken at the high TTHM locations in the distribution system.(C) Three dual sample sets must be taken at the high HAA5 locations in the distribution system.(D) Two dual sample sets must be taken at an existing R309-210-8 compliance location.(xiv) All systems must monitor during month of highest DBP concentrations.(xv) Systems on quarterly monitoring must take dual sample sets every 90 days at each monitoring location, except for subpart H systems serving 500-3,300. Systems on annual monitoring and subpart H systems serving 500- 3,300 are required to take individual TTHM and HAA5 samples (instead of a dual sample set) at the locations with the highest TTHM and HAA5 concentrations, respectively. Only one location with a dual sample set per monitoring period is needed if highest TTHM and HAA5 concentrations occur at the same location, and month, if monitored annually).(c) The water system must recommend R309-210-10 compliance monitoring locations based on standard monitoring results, system specific study results, and R309-210-8 compliance monitoring results. The water system must follow the protocol in paragraphs (c)(i) through (c)(viii) of this section. If required to monitor at more than eight locations, the water system must repeat the protocol as necessary. If the water system do not have existing R309-210-8 compliance monitoring results or if the water system do not have enough existing R309-210-8 compliance monitoring results, the water system must repeat the protocol, skipping the provisions of paragraphs (c)(iii) and (c)(vii) of this section as necessary, until the water system have identified the required total number of monitoring locations. (i) Location with the highest TTHM LRAA not previously selected as a R309-210-10 monitoring location.(ii) Location with the highest HAA5 LRAA not previously selected as a R309-210-10 monitoring location.(iii) Existing R309-210-8 average residence time compliance monitoring location (maximum residence time compliance monitoring location for ground water systems) with the highest HAA5 LRAA not previously selected as a R309-210-10 monitoring location.(iv) Location with the highest TTHM LRAA not previously selected as a R309-210-10 monitoring location.(v) Location with the highest TTHM LRAA not previously selected as a R309-210-10 monitoring location.(vi) Location with the highest HAA5 LRAA not previously selected as a R309-210-10 monitoring location.(vii) Existing R309-210-8 average residence time compliance monitoring location (maximum residence time compliance monitoring location for ground water systems) with the highest TTHM LRAA not previously selected as a R309-210-10 monitoring location.(viii) Location with the highest HAA5 LRAA not previously selected as a R309-210-10 monitoring location.(d) The water system may recommend locations other than those specified in paragraph (c) of this section if the water system include a rationale for selecting other locations. If the Director approves the alternate locations, the water system must monitor at these locations to determine compliance under R309-210-10 of this part.(e) The recommended schedule must include R309-210-10 monitoring during the peak historical month for TTHM and HAA5 concentration, unless the Director approves another month. Once the water system have identified the peak historical month, and if the water system is required to conduct routine monitoring at least quarterly, the water system must schedule R309-210-10 compliance monitoring at a regular frequency of every 90 days or fewer.Utah Admin. Code R309-210-9