Statutes, codes, and regulations
Louisiana Administrative Code
Title 43 - NATURAL RESOURCESPart XIII - Office of Conservation-Pipeline SafetySubpart 3 - Transportation of Natural Gas or Other Gas by Pipeline: Minimum Safety Standards [49 CFR Part 192]
Chapter 13 - Welding of Steel in Pipelines [49 CFR Part 192 Subpart E]
Section XIII-1309 - Limitations on Welders [49 CFR 192.229]

La. Admin. Code tit. 43 § XIII-1309

Download
PDF
Current through Register Vol. 50, No. 11, November 20, 2024
Section XIII-1309 - Limitations on Welders [49 CFR 192.229]
A. No welder whose qualification is based on nondestructive testing may weld compressor station pipe and components. [49 CFR 192.229(a)]
B. A welder or welding operator may not weld with a particular welding process unless, within the preceding 6 calendar months, the welder or welding operator was engaged in welding with that process. Alternatively, welders or welding operators may demonstrate they have engaged in a specific welding process if they have performed a weld with that process that was tested and found acceptable under section 6, 9, 12, or Appendix A of API Std 1104 (incorporated by reference, see §507) within the preceding 7 1/2 months. [49 CFR 192.229(b)]
C. A welder qualified under §1307 A: [49 CFR 192.229(c)]
1. may not weld on pipe to be operated at a pressure that produces a hoop stress of 20 percent or more of SMYS unless within the preceding 6 calendar months the welder has had one weld tested and found acceptable under the sections 6, section 9 or section 12 of API Std 1104 (incorporated by reference, see §507). Alternatively, welders or welding operators may maintain an ongoing qualification status by performing welds tested and found acceptable under the above acceptance criteria at least twice each calendar year, but at intervals not exceeding 7 1/2 months. A welder or welding operator qualified under an earlier edition of a standard listed in §507 of this Subpart may weld but may not re-qualify under that earlier edition [49 CFR 192.229(c)(1)]; and
2. may not weld on pipe to be operated at a pressure that produces a hoop stress of less than 20 percent of SMYS unless the welder is tested in accordance with Paragraph C.1 of this Section or requalifies under Paragraph D.1 or D.2 of this Section. [49 CFR 192.229(c)(2)]
D. A welder qualified under §1307. B may not weld unless: [49 CFR 192.229(d)]
1. within the preceding 15 calendar months, but at least once each calendar year, the welder has requalified under §1307 B; or [49 CFR 192.229(d)(1)]
2. within the preceding 7 1/2 calendar months, but at least twice each calendar year, the welder has had: [49 CFR 192.229(d)(2)]
a. a production weld cut out, tested, and found acceptable in accordance with the qualifying test; or [49 CFR 192.229(d)(2)(i)]
b. for a welder who works only on service lines 2 inches (51 millimeters) or smaller in diameter, the welder has had two sample welds tested and found acceptable in accordance with the test in Section III of §5105, Appendix C of this Subpart. [49 CFR 192.229(d)(2)(ii) ]

La. Admin. Code tit. 43, § XIII-1309

Promulgated by the Department of Natural Resources, Office of Conservation, LR 9:229 (April 1983), amended LR 10:521 (July 1984), LR 24:1309 (July 1998), LR 27:1541 (September 2001), LR 30:1241 (June 2004), LR 31:683 (March 2005), LR 33:479 (March 2007), Amended LR 441038 (6/1/2018), Amended LR 471143 (8/1/2021).
AUTHORITY NOTE: Promulgated in accordance with R.S. 30:501 et seq.