La. Admin. Code tit. 28 § CXXVII-305

Current through Register Vol. 50, No. 11, November 20, 2024

Section CXXVII-305 - Level Three

A. Module 27301-02. Exterior Finishing

1. Describe the purpose of wall insulation and flashing.

2. Identify the types and parts of common cornices.

3. Demonstrate the installation of selected common cornices.

4. Demonstrate lap and panel siding estimating methods.

5. Describe the types and applications of common wood siding:

a. beveled;

b. tongue-and-groove;

c. shiplap;

d. board-and-batten;

e. shake or shingle;

f. plywood;

g. hardboard and particleboard.

6. Install selected types of wood siding.

7. Describe fiber-cement siding and its uses.

8. Demonstrate the installation of fiber-cement siding.

9. Describe the types and styles of vinyl and metal siding.

10. Install selected types of vinyl or metal siding.

11. Describe the types and applications of stucco and masonry veneer finishes.

12. Describe the types and applications of special exterior finish systems.

13. Describe the types and styles of gutters and downspouts and their accessories.

14. Install selected types of metal or vinyl gutters and downspouts.

B. Module 27302-02. Roofing Applications

1. Identify the materials and methods used in roofing.

2. Explain the safety requirements for roof jobs.

3. Install fiberglass shingles on gable and hip roofs.

4. Close up a valley using fiberglass shingles.

5. Explain how to make various roof projections watertight when using fiberglass shingles.

6. Complete the proper cuts and install the main and hip ridge caps using fiberglass shingles.

7. Lay out, cut, and install a cricket or saddle.

8. Install wood shingles and shakes on roofs.

9. Describe how to close up a valley using wood shingles and shakes.

10. Explain how to make roof projections watertight when using wood shakes and shingles.

11. Complete the cuts and install the main and hip ridge caps using wood shakes/shingles.

12. Demonstrate the techniques for installing other selected types of roofing materials.

C. Module 27303-02. Thermal and Moisture Protection

1. Describe the requirements for insulation.

2. Describe the characteristics of various types of insulation material.

3. Calculate the required amounts of insulation for a structure.

4. Demonstrate the installation of selected insulation materials.

5. Describe the requirements for moisture control and ventilation.

6. Install selected vapor barriers.

7. Describe various methods of waterproofing.

8. Describe air infiltration control requirements.

9. Install selected building wraps.

D. Module 27304-02. Stairs

1. Identify the various types of stairs.

2. Identify the various parts of stairs.

3. Identify the materials used in the construction of stairs.

4. Interpret construction drawings of stairs.

5. Explain the methods of constructing various types of stairs.

6. Understand the various terms and definitions relating to stairs.

7. Lay out and cut stringers.

8. Determine the number and sizes of risers and treads required for a stairway.

9. Build a small stair unit with a handrail.

10. Lay out a skirt board.

E. Module 27305-02. Framing with Metal Studs

1. Identify the components of a metal stud system.

2. Identify and select the tools and fasteners used in a metal stud system.

3. Identify applications for metal stud systems.

4. Lay out and install a metal stud wall with openings.

5. Lay out and install a metal door frame.

6. Lay out and install a metal stud radius wall.

F. MODULE 27306-02. Drywall One: Installation

1. Identify the different types of gypsum wallboard (drywall) and their uses.

2. Select the type and thickness of drywall required for specific installations.

3. Select fasteners for drywall installation.

4. Explain the fastener schedules for different types of drywall installations.

5. Perform single-layer and multi-layer drywall installations using different types of fastening systems, including:

a. nails;

b. drywall screws;

c. adhesives.

6. Install gypsum drywall on metal studs.

7. Explain how soundproofing is achieved in drywall installations.

8. Estimate material quantities for a drywall installation.

G. Module 27307-02. Drywall Two: Finishing

1. Explain the different levels of finishing as defined in A Recommended Specification for Levels of Gypsum Board Finish.

2. Identify the hand tools used in drywall finishing and demonstrate the ability to use these tools.

3. Identify the automatic tools used in drywall finishing.

4. Identify the materials used in drywall finishing and state the purpose and use of each type of material, including:

a. compounds;

b. joint reinforcing tapes;

c. trim materials;

d. textures and coatings.

5. Demonstrate the ability to properly finish drywall using hand tools.

6. Recognize various types of problems that occur in drywall finishes and identify the cause and correct method for solving each type of problem.

7. Demonstrate the ability to patch damaged drywall.

H. Module 27308-02. Interior Finish One: Doors

1. Identify various types of door jambs and frames and demonstrate the installation procedures for placing selected door jambs and frames in different types of interior partitions.

2. Identify different types of interior doors.

3. Identify different types of interior door hardware and demonstrate the installation procedures for selected types.

4. Demonstrate the correct and safe use of the hand tools described in this module.

5. Demonstrate the correct and safe use of the power tools described in this module.

6. List and identify specific items included on a typical door schedule.

7. Demonstrate the procedure for placing and hanging a selected door.

I. Module 27309-02. Interior Finish Two: Suspended Ceilings

1. Establish a level line.

2. Understand the common terms related to sound waves and acoustical ceiling materials.

3. Identify the different types of suspended ceilings.

4. Interpret plans and shop drawings related to ceiling layout.

5. Sketch the ceiling layout for a basic suspended ceiling.

6. Perform a material takeoff for a suspended ceiling.

7. Install selected suspended ceilings.

J. Module 27310-02. Interior Finish Three: Window, Door, Floor, and Ceiling Trim

1. Identify the different types of standard moldings and describe their uses.

2. Make square and miter cuts using a miter box or power miter saw.

3. Make coped joint cuts using a coping saw.

4. Select and properly use fasteners to install trim.

5. Install interior trim, including:

a. door trim;

b. window trim;

c. base trim;

d. ceiling trim;

6. Estimate the quantities of different trim materials required for selected rooms.

K. Module 27311-02. Interior Finish Four: Cabinet Installation

1. State the classes and sizes of typical base and wall kitchen cabinets.

2. Recognize the common types of woods used to make cabinets.

3. Identify cabinet components and hardware and describe their purpose.

4. Install factory-made cabinets, countertops, and backsplashes.

5. Install plastic laminate on a countertop core.

La. Admin. Code tit. 28, § CXXVII-305

Promulgated by the Board of Elementary and Secondary Education, LR 32:1203 (July 2006).

AUTHORITY NOTE: Promulgated in accordance with R.S. 17:6(A)(10).