Ill. Admin. Code tit. 77, pt. 890, subpt. M, app A, tbl. A
All materials shall meet at least one of the approved standards listed.
Approved Building Drainage/Vent Pipe
1) | Acrylonitrite Butadiene Styrene (ABS) Pipe | ASTM D 2661-2011 | |
ASTM F 628-2012 | |||
CSA B181.1 -2011 in B1800 | |||
Joints | ASTM D 2235-2011 | ||
CSA B602-2010 | |||
Solvent Cement1 | ASTM D 2235-2011 ASTM D 3138-2011 | ||
CSA B181.1-2011 in B1800 | |||
2) | Brass Pipe | ASTM B 43-2009 | |
3) | Cast Iron Pipe | ASTM A 74-2009 | |
ASTM A 888-2011 | |||
ASTM C 564-2012 | |||
CISPI 301-2009 | |||
CSA B70-2012 FM 1680-1989 | |||
4) | Chlorinated Polyvinyl Chloride (CPVC) (Pipe and Fittings for Chemical Waste Drainage Systems) | ASTM F2618-2009 | |
5) | Copper/Copper Alloy Pipe | ASTM B 42-2010 | |
ASTM B 302-2012 | |||
6) | Copper/Copper Alloy Tubing | ASTM B 75/B75M-2011 | |
(K-L-M or DWV)2 | ASTM B 88-2009 | ||
ASTM B 251-2010 | |||
ASTM B 306-2009 | |||
7) | Galvanized Steel Pipe2 | ASTM A 53/A53M-2012 | |
8) | Glass Fiber Borosilicate Pipe3 | ASTM C 1053-2010 | |
9) | High Silicon Content Cast Iron Pipe3 | ASTM A 377-2008e1 | |
CSA B70-2012 | |||
10) | Polypropylene Pipe3 | ||
CSA B137.1 -2009 in B137 | |||
11) | Polyvinyl Chloride (PVC) Pipe and Fittings | ASTM D 2665-2012 | |
ASTM D 2949-2010 | |||
CSA B137.2 -2009 in B137 | |||
CSA B181.2 -2011 in B1800 | |||
12) | Polyvinyl Chloride (PVC) Pipe with Cellular Core4 | ASTM F891-2010 ASTM F1760-2011 | |
Joints | ASTM D 2855-2010 | ||
Primer | ASTM F 656-2010 | ||
Solvent Cement1 | ASTM D 2564-2012 ASTM D 3138-2011 | ||
13) | Polyvinylidene Fluoride3 | ASTM D 3222-2010 | |
14) | Solder | ASTM B 32-2008 | |
15) | Stainless Steel - types 304 and 316L | ASME A112.3.1-2007 (R2012) | |
16) | Stainless Steel Buttweld Fittings | ASTM A 403/A 403M-2012 ASTM A 774/A 774M-2009 | |
17) | Stainless Steel Flanges | ASTM A 2400/A 240M-2012a | |
18) | Identification of Piping Systems | ASME A13.1 -2007 | |
Agency Notes:
1 Solvent cement must be handled in accordance with ASTM F 402-1993.
2 Type M copper tubing, DWV copper tubing, and galvanized steel pipe are approved for above-ground uses only.
3 Approved for corrosive waste or corrosive soil conditions.
4 PVC pipe with cellular core is approved only for gravity drainage and venting.
5 ASME B.1.20.1-1983
Approved Materials for Building Sewer
1) | Acrylonitrite Butadiene Styrene (ABS) Pipe | ASTM D 2661-2011 | |
ASTM D 2751-2005 | |||
ASTM F 628-2012 | |||
CSA B181.1-2011 in B1800 | |||
Joints | ASTM D 2235-2011 | ||
CSA B602-2010 | |||
Solvent Cement1 | ASTM D 2235-2011 ASTM D 3138-2011 | ||
CSA B181.1-2011 in B1800 | |||
2) | Asbestos Cement Pipe | ASTM C 428/C 428M-2011e1 | |
CSA B127.1 -1999 (R2009) | |||
3) | Cast Iron Soil Pipe/Fittings | ASTM A 74-2009 | |
CSA B70-2012 | |||
Hubless Soil Pipe | CISPI 301-2009 | ||
CISPI 310-2011 | |||
CSA B70-2012 FM 1680-1989 | |||
Rubber Gaskets | ASTM C 564-2012 ASTM D 4161-2010 | ||
CSA B70-2012 | |||
CSA B602-2010 | |||
4) | Copper/Copper Alloy Tubing | ASTM B 88-2009 | |
5) | Concrete Pipe | ASTM C 14-2011 | |
ASTM C 76-2013 ASTM C 443-2012 | |||
CSA B602-2010 | |||
6) | High-Density Polyethylene (HDPE) Pipe | ASTM D 3350-2012 | |
7) | Polyvinyl Chloride (PVC) Pipe | ASTM F 1866-2007 | |
ASTM D 2665-2012 | |||
ASTM D 2949-2010 | |||
ASTM D 3034-2008 | |||
CSA B182.1 -2011 in B1800 | |||
CSA B182.2 -2011 in B1800 | |||
CSA B182.4 -2011 in B1800 | |||
CSA B181.2-2011 in B1800 | |||
Joints | ASTM D 2855-2010 ASTM D 3212-2013 | ||
CSA B602-2010 | |||
Primer | ASTM F 656-2010 | ||
Solvent Cement1 | ASTM D 2564-2012 ASTM D 3138-2011 | ||
CSA B181.2-2011 in B1800 | |||
8) | Polyvinyl Chloride (PVC) Pipe with Cellular Core2 | ASTM F 891-2010 | |
Joints | ASTM D 2855-2010 ASTM D 412-2006ae2 | ||
Primer | ASTM F 656-2010 | ||
Solvent Cement1 | ASTM D 2564-2012 ASTM D 3138-2011 | ||
9) | Solder | ASTM B 32-2008 | |
10) | Vitrified Clay Pipe2 | ASTM C 4-2009 | |
ASTM C 700-2013 ASTM C 425-2009 | |||
11) | Polypropylene Pipe2 | ASTM F 2389-2010 AWWA C901-2008 AWWA C906-2012 (Material Code PE3408)3 (Material Codes PE2406 and PE3406)4 | |
12) | Identification of Piping Systems | ASME A13.1-2007 | |
Agency Notes:
1 Solvent cement must be handled in accordance with ASTM F 402-1988.
2 PVC pipe with cellular core and vitrified clay pipe are approved only for gravity drainage.
3 Dimension Ratio (DR) 17 or less.
4 Dimension Ratio (DR) 13.5 or less.
Approved Materials for Water Service Pipe
1) | Acrylonitrite Butadiene Styrene (ABS) Pipe2 | ASTM D 1527-2005 | ||
Joints | ASTM D 2235-2011 | |||
Solvent Cement1 | ASTM D 2235-2011 | |||
2) | Brass Pipe2 | ASTM B 43-2009 | ||
3) | Cast Iron (ductile iron)2 | ASTM A 377-2008e1 | ||
Water Pipe | CSA B70-2012 AWWA C151-2009 | |||
4) | Chlorinated Polyvinyl Chloride (CPVC) Pipe2 | ASTM D 2846/D 2846M-2009be1 | ||
ASTM F 441/F 441M-2012 | ||||
ASTM F 442/F 442M-2012 | ||||
CSA B137.6 -2009 in B137 | ||||
Joints | ASTM D 2846/D 2846M-2009be1 | |||
CSA B137.6-2009 in B137 | ||||
Solvent Cement1 | ASTM F 493-2010 | |||
CSA B137.6-2009 in B137 | ||||
5) | Copper/Copper Alloy Pipe2, 3 | ASTM B 42-2010 | ||
ASTM B 302-2012 | ||||
6) | Copper/Copper Alloy Tubing2,3 | ASTM B 88-2009 | ||
7) | Galvanized Steel Pipe2 | ASTM A 53/A 53M-2012 | ||
8) | Poly Butylene (PB) Pipe/Tubing2 | CSA B137.8 -2009 in B137 | ||
9) | Polyethylene (PE) Pipe2 | ASTM D 2239-2012a AWWA C901-2008 AWWA C906-2012 (Material Code PE3408)4 (Material Codes PE2406 and PE3406)5 | ||
10) | Polyethylene (PE) Tubing2 | ASTM D 2737-2012a | ||
CSA B137.1-2009 in B137 | ||||
11) | Polypropylene Pipe2 | ASTM F 2389-2010 | ||
12) | Polyvinyl Chloride (PVC) Pipe2 | ASTM D 1785-2012 | ||
ASTM D 2241-2009 | ||||
ASTM D 2672-2009 ASTM F 477-2010 AWWA C900-2007 | ||||
CSA B137.3 -2009 in B137 | ||||
Joints | ASTM D 2855-2010 ASTM D 3139-2011 | |||
CSA B137.2-2009 in B137 | ||||
CSA B137.3-2009 in B137 | ||||
Primer | ASTM F 656-2010 | |||
Solvent Cement1 | ASTM D 2564-2012 | |||
CSA B137.3-2009 in B137 | ||||
13) | Stainless Steel Pipe2 | ASTM A 312/A 312M-2012a ASTM A 403/A 403M-2012 ASTM A 511/A 511M-2012 | ||
14) | Welded Copper Water Tube2 | ASME B31.1 -2012 ASTM B 447-2012a WK and WL | ||
15) | Solder | ASTM B 32-2008 | ||
Agency Notes:
1 Solvent cement must be handled in accordance with ASTM F 402-1988.
2 Water service pipe must meet the appropriate NSF standard for potable water.
3 Type K or L copper may be installed underground.
4 Dimension Ratio (DR) 17 or less.
5 Dimension Ratio (DR) 13.5 or less.
6 ASME B.1.20.1-1983.
Approved Materials for Water Distribution Pipe
1) | Brass Pipe2 | ASTM B 43-2009 | |||
2) | Chlorinated Polyvinyl Chloride2 (CPVC) Pipe/Tubing | ASTM D 2846/D 2846M-2009be1 | |||
ASTM F 441/F 441M-2012 | |||||
ASTM F 442/F 442M-2012 | |||||
CSA B137.6-2009 in B137 | |||||
Joints | ASTM D 2846/D 2846M-2009be1 | ||||
CSA B137.6-2009 in B137 | |||||
Solvent Cement1 | ASTM F 493-2010 | ||||
CSA B137.6-2009 in B137 | |||||
3) | Copper/Copper Alloy Pipe2 | ASTM B 42-2010 | |||
ASTM B 302-2012 AWWA C606-2011 | |||||
4) | Copper/Copper Alloy Tubing2 | ASTM B 88-2009 | |||
5) | Cross Linked Polyethylene2 | ASTM F 876-2013a | |||
5) | Distribution Systems | ASTM F 877-2011a | |||
Joints | ASTM F 1807-2012 ASTM F 1960-2012 ASTM F 2080-2012 ASTM F 2098-2008 ASTM F 2159-2011 ASSE 1061-2011 | ||||
CSA B137.5 -2009 in B137 | |||||
6) | Galvanized Steel Pipe2 | ASTM A 53-2012 AWWA C606-2011 | |||
7) | Poly Butylene (PB) Pipe/Tubing2 | ||||
CSA B137.8-2009 in B137 | |||||
8) | Polypropylene Pipe2 | ASTM F 2389-2010 | |||
9) | Polyvinyl Chloride (PVC) Pipe2, 3 | ANSI/NEMA Z535.1 -2006 (R2011) ASTM D 1785-2012 | |||
ASTM D 2241-2009 | |||||
ASTM D 2672-2009 | |||||
CSA B137.3-2009 in B137 | |||||
Joints | ASTM D 2855-2010 ASTM F 441/F 441M-2012 | ||||
CSA B137.2-2009 in B137 | |||||
CSA B137.3-2009 in B137 | |||||
Primer | ASTM F 656-2010 | ||||
Solvent Cement1 | ASTM D 2564-2012 | ||||
CSA B137.3-2009 in B137 | |||||
10) | Stainless Steel Pipe2 | ASTM A 312/A 312M-2012 ASTM A 403/A 403M-2012 ASTM A 511/A 511M-2012 | |||
11) | Welded Copper Water Tube2 | ASTM B 447-2012a WK, WL and WM | |||
12) | Solder | ASTM B 32-2008 | |||
Agency Notes:
1 Solvent cement must be handled in accordance with ASTM F 402-1988.
2 Water distribution pipe must meet the appropriate NSF standard for potable water. Plastic shall be rated at 160 psi at 73.4 degrees Fahrenheit.
3 Use for cold or tempered water only.
4 ASME B.1.20.1-1983.
5 Safety Color.
Approved Materials and Standards for
Plumbing Fixtures and Fixture Fittings
1) | Bathtub Liners (plexiglass/ABS or acrylic/plastic) | IAPMO/ANSI Z124.8 -2013 |
2) | Bathtubs, Plastic | |
CSA B45.5 -2011/IAPMO Z124-2011 | ||
3) | Bidets | ASME A112.19.2-2013/CSA B45.1 -2013 |
4) | Enameled Cast Iron and Enameled Steel Plumbing Fixtures | ASME A112.19.1-2008/CSA B45.2 -2008 |
5) | Fittings: | |
Plumbing Fixture Fittings (metering valves, faucets, etc.) | ASME A112.18.1-2012/CSA B125.1 -2012 | |
Suction Fittings for Use in Swimming Pools, Wading Pools, Spas, Hot Tubs and Whirlpool Bathtub Appliances | ANSI/APSP 16-2011 CSA C22.2 No. 218.1 -M1989 (R2011) CSA C22.2 No. 218.2 -1993 (R2008) | |
6) | Floor Drains and Trench Drains | ASME A112.6.3-2001 (R2007) |
CSA B79-2008 | ||
7) | Flushometer Bowls | ASME A112.19.2-2013/CSA B45.1-2013 |
CSA B125.3 -2011 | ||
Flushometers | ASSE 1037-1990 | |
CSA B125.3-2011 | ||
8) | Grease Interceptors | ASME A112.14.3-2000 (R2004) |
9) | Low Consumption (1.6 gpf) Water Closets1 | ASME A112.19.2-2013/CSA B45.1-2013 ASME A112.19.14-2006 (R2-11) |
10) | Plastic Lavatory | |
CSA B45.5-2011/IAPMO Z124-2011 | ||
11) | Plastic Shower Receptors/Shower Stalls | |
CSA B45.5-2011/IAPMO Z124-2011 | ||
12) | Plastic Water Closets Bowls/Tanks | |
CSA B45.5-2011/IAPMO Z124-2011 | ||
13) | Plastic Urinals Fixtures | CSA B45.5-2011/IAPMO Z124-2011 |
14) | Porcelain Enameled Formed Steel Plumbing Fixtures, including Bathtub Liners | ASME A112.19.1-2008/CSA 45.2-2008 |
15) | Stainless Steel Plumbing Fixtures (Residential) | ASME A112.19.3-2008/CSA B45.4 -2008 |
16) | Vitreous China Plumbing Fixtures | ASME A112.19.2-2013/CSA B45.1-2013 |
17) | Vitreous China Nonwater Urinals | ASME A112.19.19-2006 (R2011) |
18) | Whirlpool Bathtub Appliances | ASME A112.19.7-2012/CSA B45.10 -2012 |
CSA C22.2 No. 218.2-1993 (R2008) | ||
Agency Note:
The water pressure at each fixture installation shall meet the manufacturer's minimum recommended level for the fixture.
Approved Standards for Plumbing
Appliances/Appurtenances/Devices
1) | Anti-Backflow Freezeless Wall Hydrants | ASSE 1019-2011 |
ASME A112.18.1-2012/CSA B125.1-2012 | ||
2) | Anti-Scald Control Valve | ASSE 1016-2011/ASME A112.1016 -2011/CSA B125.16 -2011 |
3) | Anti-siphon Self-Drain Frost Proof Sillcock | ASSE 1019-2011 CSA B125.3-2012 |
4) | Automatic Ice Making Equipment | NSF/ANSI 12-2009 |
CSA C22.2 No. 120-M1991 (R2008) | ||
5) | Automatic Storage Type Water Heater Less Than 75,000 BTU/HR | ANSI Z21.10.1-2009/CSA 4.1 -2009 |
ASHRAE 90.1 2010 ASHRAE 90.2 -2007 ANSI Z21.10.1a-2009/CSA 4.1a-2009 ANSI Z21.10.1b-2011/CSA 4.1b-2011 | ||
6) | Back Water Valves | ASME A112.14.1-2003 (R2012) |
CSA B181.1-2011 in B1800 | ||
CSA B181.2-2011 in B1800 | ||
CSA B182.1-2011 in B1800 | ||
CSA B70-2012 | ||
7) | Circulating Tank, Instantaneous | ANSI Z21.10.1-2009/CSA 4.1-2009 ANSI Z21.10.1a-2009/CSA 4.1a-2009 ANSI Z21.10.1b-2011/CSA 4.1b-2011 |
ANSI Z21.10.3-2011/CSA 4.3 -2011 | ||
ANSI Z21.13 -2010/CSA 4.9 -2010 ANSI Z21.13a-2010/CSA 4.9a-2010 ANSI Z21.13b-2012/CSA 4.9b-2012 | ||
CSA B140.12 -2003 (R2008) | ||
CSA C22.2 No. 110-1994 (R2009) UL 499-2005 | ||
8) | Circulating Tank, Instantaneous, Automatic | ANSI Z21.10.3-2011/CSA 4.3-2011 ANSI Z21.13-2010/CSA 4.9-2010 ANSI Z21.13a-2010/CSA 4.9a-2010 ANSI Z21.13b-2012/CSA 4.9b-2012 UL 174-2004 |
CSA 4.1-2011 | ||
CSA B140.12-2003 (R2008) | ||
CSA C22.2 No. 110-1994 (R2009) | ||
9) | Detergent/Chemical Feeders for Commercial Use | ASSE 1055-2009 |
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 0.4 -2004 (R2009) | ||
CSA C22.2 No. 68-1992 (R2008) | ||
CSA C22.2 No. 142-M1987 (R2009) | ||
10) | Dishwashing Machine (Commercial) | ASSE 1004-2008 ANSI Z83.21 -2005/CSA C22.2 No. 168-2005 ANSI Z83.21a-2012/CSA C22.2 No. 168a-2012 |
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 0.4-2004 (R2009) | ||
11) | Dishwashing Machine (Residential) | ASSE 1006-1986 (R1989) |
CSA C22.2 No. 167-2008 | ||
12) | Diverters for Residential - Anti-Siphon | |
ASME 1112.18.1-2012/CSA B125.1-2012 | ||
13) | Double Check Detector Assembly | ASSE 1048-2011 |
CSA B64-2011 | ||
14) | Double Check With Atmospheric Vent | ASSE 1012-2009 |
CSA B64-2011 | ||
15) | Double Check Valve Assembly | ASSE 1015-2011 |
CSA B64-2011 | ||
16) | Drinking Fountains | ASHRAE 18-2008 (R2013) UL 399-2008 ASME A112.19.2-2013/CSA 45.1-13 |
17) | Drinking Water Treatment Units - Health Effects | NSF/ANSI 53-2011a |
18) | Drinking Water Treatment Units - Aesthetic Effects | NSF/ANSI 42-2011 |
19) | Drinking Water Treatment Chemicals | NSF/ANSI 60-2012 |
20) | Dual Check Valve | ASSE 1024-2004 |
CSA B64-2011 | ||
21) | Duel Check Valve (Carbonated Beverage) (Relief Port Required) | ASSE 1022-2003 CSA B64-2011 |
22) | Food Waste Disposal (Commercial) | ASSE 1009-1990 |
CSA C22.2 No. 1-2010 | ||
CSA C22.2 No. 68-1992 | ||
23) | Food Waste Disposal (Residential) | ASSE 1008-2006 |
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 68-2008 | ||
24) | Gas Water Heater Above 75,000 BTU | ANSI Z21.10.3-2011/CSA 4.3-2011 |
25) | Gas Water Heater 75,000 BTU or Less | ANSI Z21.10.1-2009/CSA 4.1-2009 ANSI Z21.10.1a-2009/CSA 4.1a-2009 |
ANSI Z21.10.1b-2011/CSA 4.1b-2011 | ||
26) | Gas Water Heater (Continuous Use) | ANSI Z21.10.1-2009/CSA 4.1-2009 ANSI Z21.10.1a-2009/CSA 4.1a-2009 |
ANSI Z21.10.1b-2011/CSA 4.1b-2011 | ||
27) | Gas Water Heater - Space Heating | ANSI Z21.10.1-2009/CSA 4.1-2009 ANSI Z21.10.1a-2009/CSA 4.1a-2009 |
ANSI Z21.10.1b-2011/CSA 4.1b-2011 | ||
28) | Grease Interceptors | PDI-G 101-2010 ASME A112.14.3-2000 (R2004) |
29) | Handheld Showers | ASSE 1014-2005 ASSE 1016-2011/ASME A112.1016-2011/CSA B125.16-2011 |
30) | Home Laundry Equipment | ASSE 1007-1986 (R1992) |
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 0.4-2004 (R2009) | ||
CSA C22.2 No. 169-1997 (R2012) | ||
31) | Hot Water Dispensers-Electrical | ASSE 1023-1979 |
CSA C22.2 No. 64-2010 | ||
32) | Hot Water Generating/Heat Recovery Equipment | NSF/ANSI 5-2012 |
33) | Ice Makers | UL 563-2009 |
CSA B45-2008 | ||
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 0.4-2004 (R2009) | ||
CSA C22.2 No. 63-1993 (R2008) | ||
CSA C22.2 No. 120-M1991 (R2008) | ||
34) | Individual Pressure Balancing In-line valves for individuals fixture fittings | ASSE 1066-1997 |
35) | Mixing Valves Automatic Compensating Valves for Individual Shower and Tub/Shower Combinations | ASSE 1016-2011/ASME A112.1016-2011/CSA B125.16-2011 |
Temperature Actuated Mixing Valves for Hot Water Distribution | ASSE 1017-2009 | |
Automatic Temperature Control Mixing Valves | ASSE 1069-2005 | |
Water Temperature Limiting Devices | ASSE 1070-2004 | |
Mixing Valves for Plumbed Emergency Equipment | ASSE 1071-2012 | |
36) | Oil Fired Water Heaters | UL 732-2010 |
CSA B140.0 -2003 (R2008) | ||
CSA B140.12-2003 (R2008) | ||
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 3-M1988 (R2009) | ||
37) | Pressure Relief Valve | ANSI Z21.22 -1999 (R2008)/CSA 4.4 -M1999 (R2008) |
ANSI Z21.22a-2000 (R2008)/CSA 4.4a-2000 (R2008) | ||
ANSI Z21.22b-2001 (R2008)/CSA 4.4b-2001 (R2008) | ||
38) | Pressurized Flushing Device | ASSE 1037-1990 |
39) | Reduced Pressure Detector Assembly | ASSE 1047-2011 |
CSA B64-2011 | ||
40) | Reduced Pressure Principle Backflow Preventer | ASSE 1013-2011 |
CSA B64-2011 | ||
41) | Refuse Compactors/Compactor System | NSF/ANSI 13-2012 |
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 68-2008 | ||
42) | Relief Valves For Hot Water System | ANSI Z21.22-1999 (R2008)/CSA 4.1-M1999 (R2008) |
ANSI Z21.22a-2000 (R2008)/CSA 4.4a-2000 (R2008) | ||
ANSI Z21.22b-2001 (R2008)/CSA 4.4b-2001 (R2008) | ||
43) | Reverse Osmosis Drinking Water Treatment System | NSF/ANSI 58-2012 |
44) | Spray Type Dishwashing Machine for Commercial Use | NSF/ANSI 3-2012 CSA C22.2 No. 0-2010 |
CSA C22.2 No. 0.4-2004 (R2009) | ||
ANSI Z83.21-2005/CSA C22.2 No. 168-2005 ANSI Z83.21a-2012/CSA C22.2 No. 168a-2012 | ||
45) | Trap Seal Primer Valve | ASSE 1018-2001 |
CSA B125.3-2012 | ||
46) | Vacuum Breakers, Anti-siphon | ASSE 1001-2008 |
CSA B64-2011 | ||
47) | Vacuum Breakers Hose Connection | ASSE 1011-2004 |
CSA B64-2011 | ||
48) | Vacuum Breaker (Laboratory Faucet) | ASSE 1035-2008 |
CSA B64-2011 | ||
49) | Vacuum Breakers Pressure Type | ASSE 1020-2004 |
CSA B64-2011 | ||
50) | Vacuum Relief Valve | ANSI Z21.22b-2001 (R2008) |
CSA B64-2011 | ||
51) | Vending Machine for Food/Beverage | NSF/ANSI 25-2012 |
CSA C22.2 No. 0-2010 | ||
CSA C22.2 No. 120-M1991 (R2008) | ||
CSA C22.2 No. 128-1995 (R2009) ASSE 1002-2008 | ||
52) | Water Closet Personal Hygiene Devices | ASME A112.4.2-2009 |
53) | Water Closet Tank Ballcock | ASSE 1002-2008 CSA B64-2011 |
CSA B125.3-2012 | ||
54) | Water Hammer Arresters | ASSE 1010-2004 |
55) | Water Heater Drain Valve | ASME A121.18.1-2011/CSA B125.1-2011 |
56) | Water Pressure Reducing Valves (Domestic) | ASSE 1003-2009 |
CSA B356-2010 | ||
57) | Water Softener and Treatment Devices | NSF/ANSI 44-2012 |
Approved Standards for Fittings
1) | Cast Iron Threaded Drainage Fittings | ASME B16.12 -2009 |
2) | Cast Copper Alloy Solder Pressure Fittings | ASME B16.18 -2012 |
3) | Cast Copper Alloy Solder Drainage Fitting (DWV) | ASME B16.23 -2011 |
4) | Copper Fittings | ASME B16.15 -2011 |
ASME B16.51 -2011 | ||
ASME B16.18-2012 | ||
ASME B16.22 -2012 | ||
ASME B16.23-2011 | ||
ASME B16.26 -2011 | ||
ASME B16.29 -2012 | ||
NSF/ANSI 61-2012 | ||
5) | Forged Steel Fittings, Socket, Welded, Threaded | ASME B16.11 -2011 |
6) | Gray Iron/Ductile Iron | AWWA C 110-2009 |
AWWA C 151-2009 | ||
7) | Malleable Iron | ASME B 16.3 -2011 |
8) | Plastic | ASTM D 2466-2006 |
ASTM D 2467-2006 | ||
ASTM D 2564-2012 | ||
ASTM F409-2012 | ||
ASTM F438-2009 | ||
ASTM F439-2012 | ||
CSA B137.3-2009 in B137 | ||
CSA B181.2-2011 in B1800 | ||
CSA B182.1-2011 in B1800 | ||
CSA B137.6-2009 in B137 | ||
CSA B137.6-1999 in B137 | ||
9) | Plumbing Fixture Fittings (Metering valves, faucets, etc.) | ASME A112.18.1-2012/CSA B125.1-2012 |
10) | Steel | ASME B 16.9 -2012 |
ASME B 16.11-2011 | ||
11) | Wrought Copper/Bronze Solder Pressure Fitting | ASME B 16.22-2012 |
12) | Wrought Copper and Wrought Copper Alloy Solder (Drainage Fittings) | ASME B16.29-2012 |
ASME B16.22-2012 | ||
13) | Wrought Steel Buttwelding Fittings | ASME B16.9-2012 |
14) | Wrought Steel Buttwelding Short Radius Ells | ASME B16.9-2012 |
Ill. Admin. Code tit. 77, pt. 890, subpt. M, app A, tbl. A