49 C.F.R. §§ 179.202-13

Current through November 30, 2024
Section 179.202-13 - Retrofit standard requirements (DOT-117R)
(a)Applicability. Each tank retrofit under these specifications must conform to the general requirements of § 179.200 and the prescriptive standards in § 179.202-13 , or the performance standard requirements of § 179.202-12 .
(b)Approval to operate at 286,000 gross rail load (GRL). A tank car may be loaded to a gross weight on rail of up to 286,000 pounds (129,727 kg) upon approval by the Associate Administrator for Safety, Federal Railroad Administration (FRA). See § 179.13 .
(c)Thickness of plates. The wall thickness after forming of the tank shell and heads must be, at a minimum, 7/16 of an inch, and constructed with steel authorized by the HMR at the time of construction.
(d)Tank head puncture resistance system. The DOT-117R specification tank car must have a tank head puncture resistance system in conformance with § 179.16(c) . The full height head shields must have a minimum thickness of 1/2 inch.
(e)Thermal protection system.
(1) The DOT Specification 117R tank car must have a thermal protection system. The thermal protection system must conform to § 179.18 of this part and include a reclosing pressure relief device in accordance with § 173.31 of this subchapter.
(2) A non-jacketed tank car modified to the DOT Specification 117R must be equipped with a thermal protection blanket with at least 1/2-inch-thick material that meets § 179.18(c) of this part.
(f)Jackets. The entire thermal protection system must be covered with a metal jacket of a thickness not less than 11 gauge A1011 steel or equivalent; and flashed around all openings so as to be weather tight. The exterior surface of a carbon steel tank and the inside surface of a carbon steel jacket must be given a protective coating.
(g)Bottom outlets. If the tank car is equipped with a bottom outlet, the handle must be removed prior to train movement or be designed with protection safety system(s) to prevent unintended actuation during train accident scenarios.
(h)Top fittings protection -
(1)Protective housing. Except as provided in §§ 179.202-13(h)(2) and (3) of this paragraph, top fittings on DOT Specification 117R tank cars must be located inside a protective housing not less than 1/2-inch in thickness and constructed of a material having a tensile strength not less than 65 kpsi and must conform to all of the following conditions:
(i) The protective housing must have a height exceeding the tallest valve or fitting which requires protection and the height of a valve or fitting within the protective housing must be kept to the minimum size compatible to allow for proper operation.
(ii) The protective housing or cover may not reduce the flow capacity of a pressure relief device below the minimum required.
(iii) The protective housing must provide a means of drainage with a minimum flow area equivalent to six (6) 1-inch diameter weep holes.
(iv) When connected to the nozzle or fitting cover plate, and subject to a horizontal force applied perpendicular to and uniformly over the projected plane of the protective housing, the tensile connection strength of the protective housing must be designed to be-
(A) no greater than 70 percent of the nozzle to tank tensile connection strength;
(B) no greater than 70 percent of the cover plate to nozzle connection strength; and
(C) no less than either 40 percent of the nozzle to tank tensile connection strength or the shear strength of twenty (20) 12-inch bolts.
(2)Pressure relief devices.
(i) The pressure relief device(s) must be located inside the protective housing, unless space does not allow for placement within a housing. If multiple pressure relief devices are installed, no more than one (1) may be located outside of a protective housing.
(ii) The height of a pressure relief device located outside of a protective housing in accordance with paragraph (h)(2)(i) of this section may not exceed the tank car jacket by more than 12 inches.
(iii) The highest point of a closure of any unused pressure relief device nozzle may not exceed the tank car jacket by more than six (6) inches.
(3)Alternative. As an alternative to the protective housing requirements in paragraph (h)(1) of this section, the tank car may be equipped with a system that prevents the release of contents from any top fitting under accident conditions where any top fitting may be sheared off.

49 C.F.R. §§179.202-13

80 FR 26749 , May 8, 2015, as amended at 81 FR 53957 , Aug. 15, 2016; 83 FR 48401 , Sept. 25, 2018; 85 FR 83403 , Dec. 21, 2020
As amended at 81 FR 53957 , 8/15/2016; 83 FR 48401 , 9/25/2018; 85 FR 83403 , 1/20/2021