Section 18 AAC 50.035 - Documents, procedures, and methods adopted by reference(a) The following documents are adopted by reference: (1) the department's In Situ Burning Guidelines for Alaska, Revision 1, revised August 2008;(2) Workbook for Plume Visual Impact Screening and Analysis (revised), EPA 454/R-92-023, October 1992;(3) the United States Environmental Protection Agency's (EPA) publication AP-42, Compilation of Air Pollutant Emission Factors, Volume: Stationary Point and Area Sources, Fifth Edition with Supplements A - F and annual updates, as updated through February 2018;(4)Meteorological Monitoring Guidance for Regulatory Modeling Applications, EPA 454/R-99-005, February 2000;(5)Ambient Monitoring Guidelines for Prevention of Significant Deterioration (PSD), EPA 450/4-87-007, May 1987;(6) the department's Title V Standard Application and Forms, revised as of March 2012;(8)Quality Assurance Handbook for Air Pollutant Measurement Systems; Volume IV: Meteorological Measurements Version 2.0 (EPA-454/B-08-002).(9) the department's letter, Inclusion of Emissions from Worker Housing Units in Air Quality Permits, dated January 30, 2017. (b) The following procedures and methods set out in 40 C.F.R., revised as of March 23, 2021, are adopted by reference: (1) 40 C.F.R. Part 50, Appendices A, C, D, F, G, J, K, L, N, P, Q, R, S, and T;(2) 40 C.F.R. Part 51, Appendix M;(4) the following test methods as they apply to 40 C.F.R. 63.11(b)(6): (A) ASTM D 1946-90(1994)e1, Standard Practice for Analysis of Reformed Gas by Gas Chromatography; and(B) ASTM D 240-92(1997)e2, Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter.(5) 40 C.F.R. Part 60, Appendices A - F;(6) 40 C.F.R. Part 63, Appendix A.(c) This subsection adopts the methods and procedures listed in this subsection for use by the department in permits for compliance monitoring. Nothing in this subsection is intended to limit the department's discretion to require in a permit issued under this chapter compliance with the requirements of other methods or procedures on a case by case basis. The following methods and procedures are adopted by reference. (1) ASTM D 129-00, Standard Test Method for Sulfur in Petroleum Products (General Bomb Method), approved January 10, 2000;(2) ASTM D 129-98, Standard Test Method for Sulfur in Petroleum Products (Lamp Method), approved February 10, 1998;(3) ASTM D 1552-95, Standard Test Method for Sulfur in Petroleum Products (High Temperature Method), approved August 15, 1995;(4) ASTM D 2622-98, Standard Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-Ray Fluorescence Spectrometry, approved April 10, 1998;(5) ASTM D 4294-98, Standard Test Method for Sulfur in Petroleum and Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry, approved April 10, 1998;(6) ASTM D 4045-99, Standard Test Method for Sulfur in Petroleum Products by Hydrogenolysis and Rateometric Colorimetry, approved January 10, 1999;(7) ASTM D 2492-90 (Reapproved 1998), Standard Test Method for Forms of Sulfur in Coal, approved March 30, 1990;(8) ASTM D 3176-89 (Reapproved 1997), Standard Practice for Ultimate Analysis of Coal and Coke, approved September 29, 1989;(9) ASTM D 4749-87 (Reapproved 1994), Standard Test Method for Performing the Sieve Analysis of Coal and Designating Coal Size, approved November 27, 1987;(10) ASTM D 1140-97, Standard Test Method for Amount of Material in Soils Finer Than the No. 200 Sieve, approved May 10, 1997;(11) ASTM D 422-63 (Reapproved 1998), Standard Test Method for Particle-Size Analysis of Soils, approved November 21, 1963;(12) ASTM D 4629-96, Standard Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection, approved April 10, 1996;(13) ASTM D 5762-98, Standard Test Method for Nitrogen in Petroleum and Petroleum Products by Boat-Inlet Chemiluminescence, approved December 10, 1998;(14) ASTM D 4913-89 (Reapproved 1995), Standard Practice for Determining Concentration of Hydrogen Sulfide by Direct Reading, Length of Stain, Visual Chemical Detectors, approved February 24, 1989;(15) ASTM D 4810-88 (Reapproved 1999), Standard Test Method for Hydrogen Sulfide in Natural Gas Using Length-of-Stain Detector Tubes, approved April 29, 1988;(16) ASTM D 6216-98, Standard Practice for Opacity Monitor Manufacturers to Certify Conformance with Design and Performance Specifications, approved February 10, 1998;(17) ASTM D 4239-00, Standard Test Methods for Sulfur in the Analysis Sample of Coal and Coke Using High-Temperature Tube Furnace Combustion Methods, approved April 10, 2000. Eff. 1/18/97, Register 141; am 6/21/98, Register 146; am 7/2/2000, Register 154; am 2/2/2002, Register 161; am 5/3/2002, Register 162; am 10/1/2004, Register 171; am 12/3/2005, Register 176; am 7/25/2008, Register 187; am 11/9/2008, Register 188; am 4/1/2010, Register 193; am 9/17/2011, Register 199; am 4/8/2012, Register 202; am 9/14/2012, Register 203; am 1/4/2013, Register 205; am 4/17/2015, Register 214, July 2015; am 8/20/2016, Register 219, October 2016; am 9/15/2018, Register 227, October 2018; am 11/7/2020, Register 236, January 2021; am 4/16/2022, Register 242, July 2022Authority:AS 46.03.020
AS 46.14.010
AS 46.14.020
AS 46.14.030
AS 46.14.140
Sec. 30, ch. 74, SLA 1993