Airworthiness Directives; Rolls-Royce Deutschland Ltd & Co KG (Type Certificate Previously Held by Rolls-Royce plc) Engines

AGENCY:

Federal Aviation Administration (FAA), DOT.

ACTION:

Notice of proposed rulemaking (NPRM).

SUMMARY:

The FAA proposes to supersede Airworthiness Directive (AD) 2020–15–07, which applies to certain Rolls-Royce Deutschland Ltd & Co KG (RRD) (type certificate previously held by Rolls-Royce plc) Model RB211–524G2–19, RB211–524G2–T–19, RB211–524G3–19, RB211–524G3–T–19, RB211–524H2–19, RB211–524H2–T–19, RB211–524H–36, and RB211–524H–T–36 engines. AD 2020–15–07 requires replacement of the low-pressure turbine (LPT) stage 1 disk with part number (P/N) UL37606, UL37607, UL37608, UL37722 or UL37790, installed. Since the FAA issued AD 2020–15–07, RRD determined that additional LPT stage 1 disks are affected by the unsafe condition, and updated the Aircraft Maintenance Manual (AMM) to add new component life limits. This proposed AD would retain the requirement to replace the LPT stage 1 disk and would include additional LPT stage 1 disks, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

DATES:

The FAA must receive comments on this NPRM by August 28, 2023.

ADDRESSES:

You may send comments, using the procedures found in 14 CFR 11.43 and 11.45, by any of the following methods:

• Federal eRulemaking Portal: Go to regulations.gov. Follow the instructions for submitting comments.

• Fax: (202) 493–2251.

• Mail: U.S. Department of Transportation, Docket Operations, M–30, West Building Ground Floor, Room W12–140, 1200 New Jersey Avenue SE, Washington, DC 20590.

• Hand Delivery: Deliver to Mail address above between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays.

AD Docket: You may examine the AD docket at regulations.gov under Docket No. FAA–2023–1399; or in person at Docket Operations between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD docket contains this NPRM, the mandatory continuing airworthiness information (MCAI), any comments received, and other information. The street address for Docket Operations is listed above.

Material Incorporated by Reference:

• For service information that is proposed for IBR in this NPRM, contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999 000; email: ADs@easa.europa.eu; website: easa.europa.eu. You may find this material on the EASA website at ad.easa.europa.eu. It is also available at regulations.gov under Docket No. FAA–2023–1399.

• You may view this service information at the FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (817) 222–5110.

FOR FURTHER INFORMATION CONTACT:

Sungmo Cho, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 238–7241; email: Sungmo.D.Cho@faa.gov.

SUPPLEMENTARY INFORMATION:

Comments Invited

The FAA invites you to send any written relevant data, views, or arguments about this proposal. Send your comments to an address listed under ADDRESSES . Include “Docket No. FAA–2023–1399; Project Identifier MCAI–2022–01533–E” at the beginning of your comments. The most helpful comments reference a specific portion of the proposal, explain the reason for any recommended change, and include supporting data. The FAA will consider all comments received by the closing date and may amend the proposal because of those comments.

Except for Confidential Business Information (CBI) as described in the following paragraph, and other information as described in 14 CFR 11.35, the FAA will post all comments received, without change, to regulations.gov including any personal information you provide. The agency will also post a report summarizing each substantive verbal contact received about this NPRM.

Confidential Business Information

CBI is commercial or financial information that is both customarily and actually treated as private by its owner. Under the Freedom of Information Act (FOIA) (5 U.S.C. 552), CBI is exempt from public disclosure. If your comments responsive to this NPRM contain commercial or financial information that is customarily treated as private, that you actually treat as private, and that is relevant or responsive to this NPRM, it is important that you clearly designate the submitted comments as CBI. Please mark each page of your submission containing CBI as “PROPIN.” The FAA will treat such marked submissions as confidential under the FOIA, and they will not be placed in the public docket of this NPRM. Submissions containing CBI should be sent to Sungmo Cho, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198. Any commentary that the FAA receives which is not specifically designated as CBI will be placed in the public docket for this rulemaking.

Background

The FAA issued AD 2020–15–07, Amendment 39–21170 (85 FR 43682, July 20, 2020), (AD 2020–15–07), for RRD Model B211–524G2–19, RB211–524G2–T–19, RB211–524G3–19, RB211–524G3–T–19, RB211–524H2–19, RB211–524H2–T–19, RB211–524H–36, and RB211–524H–T–36 engines with LPT stage 1 disks, part number (P/N) UL37606, UL37607, UL37608, UL37722 or UL37790, installed. AD 2020–15–07 was prompted by an MCAI originated by EASA, which is the Technical Agent for the Member States of the European Union. EASA issued EASA AD 2020–0059, dated March 17, 2020 (EASA AD 2020–0059), to address an unsafe condition identified as an updated analysis by the engine manufacturer indicating that certain part-numbered and serial-numbered LPT stage 1 disks that have undergone rework could fail before the current published life limits.

AD 2020–15–07 requires replacement of the LPT stage 1 disk before it reaches its new Declared Safe Cycle Limit (DSCL) or within 25 flight cycles after the effective date of AD 2020–15–07, whichever occurs later. The FAA issued AD 2020–15–07 to prevent failure of the LPT stage 1 disk.

Actions Since AD 2020–15–07 Was Issued

Since the FAA issued AD 2020–15–07, EASA superseded EASA AD 2020–0059 and issued EASA AD 2022–0237, dated December 2, 2022 (EASA AD 2022–0237) (referred to after this as the MCAI). The MCAI states that further investigation by the manufacturer identified additional part numbered LPT stage 1 disks affected by the unsafe condition. As a result of this finding, RRD published revised service information, which includes the additional affected LPT stage 1 disk part numbers.

The FAA is proposing this AD to prevent failure of the LPT stage 1 disk. This condition, if not addressed, could result in uncontained release of high-energy debris from the engine, in-flight shutdown of the engine, damage to the engine, and damage to the airplane.

You may examine the MCAI in the AD docket at regulations.gov under Docket No. FAA–2023–1399.

Related Service Information Under 1 CFR Part 51

The FAA reviewed EASA AD 2022–0237, which specifies procedures for replacement of the LPT stage 1 disk and reducing the DSCL for LPT stage 1 disks. This material is reasonably available because the interested parties have access to it through their normal course of business or by the means identified in ADDRESSES .

FAA's Determination

These products have been approved by the aviation authority of another country and are approved for operation in the United States. Pursuant to the FAA's bilateral agreement with this State of Design Authority, it has notified the FAA of the unsafe condition described in the MCAI described above. The FAA is issuing this NPRM after determining that the unsafe condition described previously is likely to exist or develop on other products of the same type design.

Proposed AD Requirements in This NPRM

This proposed AD would retain none of the requirements of AD 2020–15–07. This proposed AD would include additional LPT stage 1 disks and require accomplishing the actions specified in the MCAI described previously, except for any differences identified as exceptions in the regulatory text of this proposed.

Explanation of Required Compliance Information

In the FAA's ongoing efforts to improve the efficiency of the AD process, the FAA developed a process to use some civil aviation authority (CAA) ADs as the primary source of information for compliance with requirements for corresponding FAA ADs. The FAA has since coordinated with other manufacturers and CAAs to use this process. As a result, the FAA proposes to incorporate by reference EASA AD 2022–0237 in the FAA final rule. This proposed AD would, therefore, require compliance with EASA AD 2022–0237 in its entirety through that incorporation, except for any differences identified as exceptions in the regulatory text of this proposed AD. Using common terms that are the same as the heading of a particular section in the EASA AD does not mean that operators need comply only with that section. For example, where the AD requirement refers to “all required actions and compliance times,” compliance with this AD requirement is not limited to the section titled “Required Action(s) and Compliance Time(s)” in EASA AD 2022–0237. Service information required by the EASA AD for compliance will be available at regulations.gov under Docket No. FAA–2023–1399 after the FAA final rule is published.

Costs of Compliance

The FAA estimates that this AD, if adopted as proposed, would affect 18 engines installed on airplanes of U.S. registry.

The FAA estimates the following costs to comply with this proposed AD:

Authority for This Rulemaking

Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority.

The FAA is issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701: General requirements. Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action.

Regulatory Findings

The FAA determined that this proposed AD would not have federalism implications under Executive Order 13132. This proposed AD would not have a substantial direct effect on the States, on the relationship between the national Government and the States, or on the distribution of power and responsibilities among the various levels of government.

For the reasons discussed above, I certify that the proposed regulation:

(1) Is not a “significant regulatory action” under Executive Order 12866,

(2) Would not affect intrastate aviation in Alaska, and

(3) Would not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act.

List of Subjects in 14 CFR Part 39

• Air transportation
• Aircraft
• Aviation safety
• Incorporation by reference
• Safety

The Proposed Amendment

Accordingly, under the authority delegated to me by the Administrator, the FAA proposes to amend 14 CFR part 39 as follows:

PART 39—AIRWORTHINESS DIRECTIVES

1. The authority citation for part 39 continues to read as follows:

Authority: 49 U.S.C. 106(g), 40113, 44701.

2. The FAA amends § 39.13 by:

a. Removing Airworthiness Directive 2020–15–07, Amendment 39–21170 ( 85 FR 43682, July 20, 2020); and

b. Adding the following new airworthiness directive:

Rolls-Royce Deutschland Ltd. & Co. KG: Docket No. FAA–2023–1399; Project Identifier MCAI–2022–01533–E.

(a) Comments Due Date

The FAA must receive comments on this airworthiness directive (AD) by August 28, 2023.

(b) Affected ADs

This AD replaces AD 2020–15–07, Amendment 39–21170 (85 FR 43682, July 20, 2020).

(c) Applicability

This AD applies to Rolls-Royce Deutschland Ltd & Co. KG (RRD) Model RB211–524G2–19, RB211–524G2–T–19, RB211–524G3–19, RB211–524G3–T–19, RB211–524H2–19, RB211–524H2–T–19, RB211–524H–36, and RB211–524H–T–36 engines.

(d) Subject

Joint Aircraft System Component (JASC) Code 7250, Turbine Section.

(e) Unsafe Condition

This AD was prompted by an updated analysis by the engine manufacturer, which indicates certain part-numbered and serial-numbered low-pressure turbine (LPT) stage 1 disks that have undergone rework could fail before the current published life limits. The FAA is issuing this AD to prevent failure of the LPT stage 1 disk. The unsafe condition, if not addressed, could result in uncontained release of high-energy debris from the engine, in-flight shutdown of the engine, damage to the engine, and damage to the airplane.

(f) Compliance

Comply with this AD within the compliance times specified, unless already done.

(g) Required Actions

Except as specified in paragraphs (h) of this AD: Perform all required actions within the compliance times specified in, and in accordance with, European Union Aviation Safety Agency (EASA) AD 2022–0237, dated December 2, 2022 (EASA AD 2022–0237).

(h) Exceptions to EASA AD 2022–0237

(1) Where EASA AD 2022–0237 refers to its effective date, this AD requires using the effective date of this AD.

(2) This AD does not adopt the Remarks paragraph of EASA AD 2022–0237.

(i) Alternative Methods of Compliance (AMOCs)

(1) The Manager, AIR–520, Continued Operational Safety Branch, FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. In accordance with 14 CFR 39.19, send your request to your principal inspector or local Flight Standards District Office, as appropriate. If sending information directly to the manager of the certification office, send it to the attention of the person identified in paragraph (j) of this AD and email to: ANE-AD-AMOC@faa.gov.

(2) Before using any approved AMOC, notify your appropriate principal inspector, or lacking a principal inspector, the manager of the local flight standards district office/certificate holding district office.

(j) Additional Information

For more information about this AD, contact Sungmo Cho, Aviation Safety Engineer, FAA, 2200 South 216th Street, Des Moines, WA 98198; phone: (781) 238–7241; email: Sungmo.D.Cho@faa.gov.

(k) Material Incorporated by Reference

(1) The Director of the Federal Register approved the incorporation by reference (IBR) of the service information listed in this paragraph under 5 U.S.C. 552(a) and 1 CFR part 51.

(2) You must use this service information as applicable to do the actions required by this AD, unless the AD specifies otherwise.

(i) European Union Aviation Safety Agency AD 2022–0237, dated December 2, 2022.

(ii) [Reserved]

(3) For EASA AD 2022–0237 contact EASA, Konrad-Adenauer-Ufer 3, 50668 Cologne, Germany; phone: +49 221 8999 000; email: ADs@easa.europa.eu; website: easa.europa.eu. You may find this EASA AD on the EASA website at ad.easa.europa.eu.

(4) You may view this service information at FAA, Airworthiness Products Section, Operational Safety Branch, 1200 District Avenue, Burlington, MA 01803. For information on the availability of this material at the FAA, call (817) 222–5110.

(5) You may view this service information that is incorporated by reference at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, email: fr.inspection@nara.gov, or go to: www.archives.gov/federal-register/cfr/ibr-locations.html.